– 8-way switch to select between delay types.
Indicates the currently loaded preset.
– Press to cycle through the 32 preset banks.
We’d like to thank you for making the Seymour Duncan Andromeda Dynamic Delay a part of
your tone quest. In your hands is a powerful creative tool that combines classic delay sounds
with unique dynamic control for an inspiring musical experience.
To download the Andromeda software, review tech specs and check out sample presets,
– Press to cycle through the 4 presets (A/B/C/D) in the currently selected bank.
Press both Bank and Preset buttons together to enter SAVE mode. Display will flash. Use Bank and Preset
buttons to choose a save location then press both buttons together again to Save the current UI state to
the selected preset location.
Sets the desired number of delay repeats. Turning the FEEDBACK knob clockwise
will give you more delay repeats, up to infinite. In Analog mode the delay will enter runaway feedback.
DELAY TIME KNOB
– Knob that controls the delay time. Using this knob overrides any preset Tempo
or Tap Value set by the tap footswitch.
TAP VALUE KNOB
– 4-way switch to set note division of the delay time.
– Knob to control the sensitivity of the Dynamic Expression feature. The LED will
illuminate brighter when there is more of the selected parameter blended in, and dim when there is less.
– Toggles the Dynamic Expression between its two modes or turns it off.
HARD MODE – Blends in more of the selected parameter (Mix, Mod, or Saturation) when you play harder
SOFT MODE – Blends in more of the selected parameter when you play softer.
– Selects the parameter that the Dynamic Expression feature
– Adds pleasant overdrive and ‘grit’ to the wet signal (repeats). This is similar to
– Control to brighten or darken the sound of the wet signal.
– Blends in a Chorus effect on the wet signal.
– Determines balance of wet/dry signal.
Fully clockwise = 100% wet.
Fully counter-clockwise= 100% dry.
– When set to ON the delay will continue to decay naturally when bypassed.
(No new repeats will be generated). In this mode Andromeda uses a buffered bypass.
When set to OFF the delay will cut off as soon as the effect is bypassed. In this mode Andromeda is
– Turns delay on and off. Hold for Freeze. Be aware that in analog mode feedback
can run away and create loud or unpleasant noise.
– Defaults to TAP mode, tap the footswitch two or more times to set
the tempo of the delay. To change to PRESET mode press and hold the footswitch until the LED stops
blinking and becomes solid, then press the footswitch to scroll through the four presets in the current
bank. After 2 seconds the mode will revert to TAP.
In the unlikely event that you ever need to dispose of this product it must be disposed of properly by handing it
over to a designated collection point for the recycling of waste electronic equipment. Please contact your local
household waste disposal service or the shop where you purchased this product for those locations. Thanks for
helping us conserve natural resources and ensure that it is recycled in a manner that protects human health
and the environment.
Seymour Duncan offers the original purchaser a one-year limited warranty on both labor and materials
from the day this product is purchased. We will repair or replace this product at our option if it fails due to
faulty workmanship or materials during this period. Defective products can be returned to your USA dealer,
international distributor, or sent direct to our factory postage prepaid along with dated proof of purchase (e.g.,
original store receipt) and RMA number. Call or email our factory for an RMA number which must be written
We reserve the right to refuse boxes without an RMA written on the outside. As
you might expect this warranty does not apply if you’ve modified the unit or treated it unkindly. We can assume
no liability for any incidental or consequential damages which may result from the use of this product. Any
warranties implied in fact or by law are limited to the duration of this express limited warranty.
COMMITMENT TO QUALITY AND COMMUNITY
Seymour Duncan takes pride in designing and crafting our products to create the most amazing sound
possible. Our Made in the USA label designates that the products are designed in Santa Barbara, California
and manufactured in the USA with quality parts sourced in the United States and around the world.
With everything we create, our passion and obsession for amazing sound is reflected in its quality and
It’s the heart.
The core of the sound.
Because soul matters.
We stand for quality.
We’re an American original.
An industry leader.
And we’re always innovating.
Our passion. Our history.
It’s in everything we build.
In everything we touch.
Music. Power. Heart. Soul. Tone.
It’s who we are. It’s what we do.
We are Seymour Duncan.
5427 Hollister Ave
Santa Barbara, CA 93111