Microsoft Word Infinity Max Specifications doc



Yüklə 55,14 Kb.
Pdf görüntüsü
tarix15.03.2018
ölçüsü55,14 Kb.
#32191


 

 

 



 

 

 

 



 

www.InfinityPerformance.com 888-479-1017 

 

 

INFINITY MAX™ TILE SPECIFICATION 

 

Physical Specification: INFINITY MAX™ configurations consist of an interlocking, dual 

durometer flooring system consisting of a high density wear layer surface permanently molded 

to an underlayment incorporating 113 pedestals per tile to maximize shock absorbency and 

traction underfoot in wet and dry conditions as well as an omni-directional locking design to 

promote ease of installation. 

 

Component Specification: INFINITY MAX™  is a factory molded modular surfacing system 

composed of high quality TPV (ThermoPlastic Volcanisate) rubber granules bound in both 

underlayment and wear surface with a wear and weather resistant polyurethane. Rubber 

granules in both wear surface and underlayment are specially blended to enhance tile strength, 

durability and energy absorption characteristics. 

 

Tile Construction: INFINITY MAX™ 

1.  Evenly distributes fitness equipment weight over 113 pedestals per tile 

2.  Omni-Directional Locking Design: Locks the system firmly in place without adhesive 

3.  Wear Layer: High compression wear layer 

                       Type: Virgin TPV rubber granules.  

 

INFINITY MAX™ TILE SPECIFICATION 

 

 

 



 

 

Product Data 



 

 

Dimensions (78° F.): 

 

1.25” x 23.75” x 23.75” ± 1/8” 



Wear Surface Density 

 

90 lb./ft



3

 min. 


Coefficient of Thermal Expansion 

 

1.1 x 10



-3

 in/ft/°F 

Weight 

 

21.5 lbs./tile or 5.3 lb./ft



2

 

Physical Data Test 

 

ASTM 

 

Acoustical A09-009



 

EC423 / 


E795

 

SAA =0.14, NRC = 0.15



 

Acoustical TL08-363

 

E90 / E413



 

STC = 53


 

Acoustical IN08-050

 

E492 / E989



IIC – 59

 

Acoustical IFC09-002



 

E2179


 

DELTA IIC 26 IICc 54

 

Tensile Strength 



D412 

107 lb/in

2

 min 


Elongation at Break 

D412 


165% minimum  

Compression Deflection 

D1667 

29.5 lb/in



to 25% Compression 

Compression Set 

D395 


4.37% Permanent Set 

Impact Insulation Class 

E49 

> 50 


Tear Resistance 

D624 


33.1 lb./in

2

 min. 



Slip Resistance 

E303 


Dry: 102, Wet: 62 

Coefficient of Friction

 (

Slip Resistance) 



D2047 

Dry .81 Wet .82 

Noise Reduction Coefficient 

C423 


0.10 sabine/ft

2

Rubber Deterioration / Air Oven 



D573 

No Deterioration 

Critical Radiant Flux 

E648 


Class II - .34 

Flammability E648 

Class 



Flammability 



(Burning Pill Test)

 D2859 


Passed 

Flammability – Roof Covering 

E108 

Class A 


Freeze Thaw 

C67 


No Deterioration 


 

 

 



 

 

 

 

 

 

 

 

 



SECTION 02790 

 

ATHLETIC AND RECREATIONAL SURFACING 

 

1.1 QUALITY ASSURANCE 

A. 

Manufacturer's Qualifications:  Manufacturer shall meet at least one of the following 



requirements. 

1. 


Continuously engaged in manufacturing of surfacing products of similar type to that 

specified, with a minimum of 10 years successful experience. 

2. 

Furnished a minimum of 1,000,000 square feet per year of surfacing products of 



similar type to that specified. 

B. Installer's 

Qualifications: 

1. 


Successful experience in installation of surfacing of similar type to that specified, with 

a minimum of 25 projects completed within last 5 years. 

2. 

Employ persons trained for installation of surfacing products. 



3. 

Must be installed by the Manufacturer’s own installation crew or Manufacturer 

Approved Installer. 

1.2  

DELIVERY, STORAGE, AND HANDLING 

A. 


Delivery:  Deliver materials to site in manufacturer's original, unopened containers and 

packaging, with labels clearly identifying product name and manufacturer. 

B. Storage: 

1. 


Store materials in accordance with manufacturer's instructions. 

2. 


Store materials in a dry storage area at a minimum temperature of 50 degrees F (10 

degrees C) for a minimum of 48 hours before installation. 

3. 

Store materials to be installed indoors at the ambient temperature of the installation 



location for a minimum of 48 hours before installation. 

4. 


Protect materials from direct sunlight before installation. 

5. 


Store adhesive in a dry area at a minimum temperature of 50 degrees F  

C. 


Handling:  Protect materials during handling and installation to prevent damage. 

D. 


Store and dispose of solvent-based materials, and materials used with solvent-based 

materials, in accordance with requirements of local authorities having jurisdiction. 



1.3  

PROJECT CONDITIONS 

A. 


Maintain environmental conditions (temperature, humidity, and ventilation) within limits 

recommended by manufacturer for optimum results.  Do not install products under 

environmental conditions outside manufacturer's absolute limits. 

1. 


Material Temperature:  Ensure surface temperature of surfacing tiles is a minimum of 

50 degrees F (10 degrees C) at time of installation. 

2. 

Air Temperature for Interior Installations:  Ensure air temperature is at the same 



temperature as anticipated during normal operation. 

3. 


Air Temperature for Exterior Installations:  Ensure air temperature is a minimum of 40 

degrees F (4 degrees C) and a maximum of 90 degrees F (32 degrees C) for a 

minimum of 24 hours before and during installation. 

 



 

 

 



 

 

 

 

 

 

 

1.4  



SUBMITTALS 

A. 


Submit under provisions of Section 01300. 

B. 


Product Data:  Manufacturer's data sheets on each product to be used, including: 

1. 


Preparation instructions and recommendations. 

2. 


Storage and handling requirements and recommendations. 

3. Installation 

methods. 

C. 


Selection Samples:  For each finish product specified, two complete sets of color chips 

representing manufacturer's full range of available colors and patterns. 

D. 

Verification Samples:  For each finish product specified, two samples, minimum size 6 



inches (150 mm) square, representing actual product, color, and patterns. 

E. 


Certificate of Compliance:  Submit manufacturer's certificate of compliance indicating 

materials comply with specified requirements. 

F. 

Manufacturer's Project References: 



1. 

Submit list of successfully completed projects. 

2. 

Include project name and location, name of architect, and type and quantity of 



surfacing furnished. 

G. 


Installer's Project References: 

1. 


Submit list of successfully completed projects. 

2. 


Include project name and location, name of architect, and type and quantity of 

surfacing installed. 

H. 

Maintenance Instructions:  Submit manufacturer's maintenance and cleaning instructions. 



I. 

Warranty:  Submit manufacturer's standard warranty. 

 

1.5  

WARRANTY 

 

INFINITY MAX™ is warranted for a period of 10 (ten) years against premature deterioration, 



manufacturer’s defects as well as any damage whatsoever to the INFINITY MAX™ material due to 

dropping free weights directly on the INFINITY MAX™.   

 

The warranty issued for this project must have the following statement included in the material 



warranty:  “Seller warrants that any damage to the INFINITY MAX™ material due to dropping free 

weights on the INFINITY MAX™ will be covered under this warranty for a period of ten (10) years.”   

 

 

 



 

 

 




 

 

 



 

 

 



 

PART  2  PRODUCTS 

2.1  

MANUFACTURERS 

A. Acceptable 

Manufacturer: 

Infinity Performance Inc., which is located at: 6735 N. Meridian 

St., Indianapolis, IN  46260. Email: 

info@infinityperformance.com

; Web: 


www.InfinityPerformance.com

  

B. Requests 



for 

substitutions 

will be considered in accordance with provisions of Section 

01600. 


2.2  

FITNESS FLOORING 

A. 


INFINITY MAX™ as manufactured for Infinity Performance Inc. 

1. 


Manufactured with a TPV rubber granule on the wear layer to provide a speckled 

appearance.  Any combination of colors can be used to create a speckled 

appearance. 

2. 


Blend:  90 percent color, 10 percent black. 

B. Tile 


Construction: 

1. 


Evenly distributes fitness equipment weight over 64 pedestals per tile. 

2. 


Omni-Directional Locking Design: Locks the system firmly in place with or without the 

use of adhesive. 

3. 

Wear Layer: High compression wear layer. 



a. 

Type: Virgin TPV rubber granules.  Nominal 0.250 inch (6 mm) thick. 

4. 

Size:  23.75 inches by 23.75 inches, plus or minus 1/8 inch 



5. 

Thickness:  1.25 inches 

6. 

Freeze Thaw, ASTM C 67:  No deterioration. 



7. 

Rubber Deterioration / Air Oven, ASTM D 573:  No deterioration. 

8. Slip 

Resistance: 

a. 

ASTM E 303: 



1) 

Dry:  102. 

2) 

Wet:  62. 



b. 

ASTM D 2047: 

1) 

Dry:  0.81. 



2) 

Wet:  0.82. 

9. 

Compression Deflection, ASTM D 1667:  29.5 psi (2.1 kgs/sq. cm) to 25 percent 



compression. 

10. 


Compression Set, ASTM D 395:  4.37 percent permanent set. 

11. 


Tensile Strength, ASTM D 412:  107 psi (7.5 kgs/sq. cm). 

12. 


Elongation at Break, ASTM D 412:  165 percent. 

13. 


Tear Strength, ASTM D 624: 33.1 psi (2.3 kgs/sq. cm). 

14. 


Wear Surface Density (Durability):  90 pcf (961 kg/cu. m) minimum. 

15.     Critical Radiant Flux, ASTM E 648: Class II, .34 

16. Flammability: 

a. 


Burning Pill, ASTM D 2859:  Pass. 

C. Accessories: 

1. Corners: 

a. 


Prefabricated outside and inside corners. 

b. 


Material:  Same as surfacing tiles. 

2. Ramps: 

a. Prefabricated 

Ramps 


b. 

Prefabricated ADA-Compliant Ramps 




 

 

c. 



Material:  Same as surfacing tiles. 

 

 



 

 

 



 

 

 



PART  3  EXECUTION 

3.1  

EXAMINATION 

A. 


Do not begin installation until substrates have been properly prepared. 

B. 


If substrate preparation is the responsibility of another installer, notify Architect of 

unsatisfactory preparation before proceeding. 



3.2  

PREPARATION 

A. 


Clean surfaces thoroughly prior to installation. 

B. 


Prepare surfaces using the methods recommended by the manufacturer for achieving the 

best result for the substrate under the project conditions. 

C. 

Subsurface:  Install adhesive at the perimeter of the installation as recommended by the 



manufacturer. 

D. 


Variations in Elevation:  Repair variations in elevation of completed subsurface greater than 

plus or minus 1/4 inch (6 mm) over 10 feet (3 m) in any direction. 



3.3  

INSTALLATION 

A. 


Install surfacing in accordance with manufacturer's instructions at locations indicated on the 

Drawings. 

B. 

Ensure prepared subsurface is dry and clean. 



C. 

Layout surface pattern in accordance with manufacturer's instructions. 



3.4  

CLEANING 

A. 


Clean tiles in accordance with manufacturer's instructions. 

3.5  

PROTECTION 

A. 


Protect completed tiles from damage during construction. 

 

END OF SECTION 



 

 

The products in this specification are based on the products of: 



 

Infinity Performance, Inc. 

6735 N. Meridian Street 

Indianapolis, IN  46260 

 

Toll Free:      (888) 479-1017 



Tel: 

        (317) 479-1017 

Fax: 

        (317) 479-1018 



 

E-mail:          

info@infinityperformance.com

Web:             

www.infinityperformance.com

 

 



 

 

Document Outline


Yüklə 55,14 Kb.

Dostları ilə paylaş:




Verilənlər bazası müəlliflik hüququ ilə müdafiə olunur ©genderi.org 2024
rəhbərliyinə müraciət

    Ana səhifə