Microsoft Word sop osmium Tetroxide doc



Yüklə 55,43 Kb.
Pdf görüntüsü
tarix02.03.2018
ölçüsü55,43 Kb.
#29561


UCLA
Chemistry
&
Biochemistry

Procedures
for
Safe
Use
of
Osmium
Tetroxide
12/2009




Page
1
of
5



Standard Operating Procedure 



Working with Osmium Tetroxide 

  

 

Osmium tetroxide, aka Osmic acid, perosmic oxide, osmium(IV) oxide,  OsO



4

   CAS 20816-12-0  

 

I. PERMISSIBLE EXPOSURE LIMIT:

 Cal-OSHA PEL= 0.0002 ppm (0.002 mg/m

3

)   


Mp 40 

o

C, bp 130 



o

C, Vapor Pressure 7 mm Hg at 20 

o

C,  


 

II. MEDICAL SURVEILLANCE: 

Under usual circumstances medical evaluation is not necessary.  However, in 

the case of skin contamination and/or possible personal exposure including symptoms such as eye irritation, the 

personnel must get a medical evaluation. The exposure must be reported to the Chemical Safety Officer.   

 

III. HAZARDS SUMMARY:

 Oxidizing material.  Highly toxic.  Contact with combustible materials may cause 

fire.  May cause sensitization by inhalation or skin contact.    

 

ACUTE

The acute toxicity of osmium tetroxide is high, and it is a severe irritant of the eyes and respiratory tract. 

Exposure to osmium tetroxide vapor can damage the cornea of the eye. Irritation is generally the initial symptom of 

exposure to low concentrations of osmium tetroxide vapor, and lacrimation, a gritty feeling in the eyes, the eyes can 

temporarily cloud, and the appearance of rings around lights may also be noted. In most cases, recovery occurs in a 

few days. Concentrations of vapor that do not cause immediate irritation can have an insidious cumulative effect; 

symptoms may not be noted until several hours after exposure. Contact of the eyes with concentrated solutions of 

this substance can cause severe damage and possible blindness.  

 

Inhalation can cause headache, coughing, dizziness, lung damage, and difficult breathing and may be fatal. 



Contact of the vapor with skin can cause dermatitis, and direct contact with the solid can lead to severe irritation and 

burns. Exposure to osmium tetroxide via inhalation, skin contact, or ingestion can lead to systemic toxic effects 

involving liver and kidney damage. Osmium tetroxide is regarded as a substance with poor warning properties.   

 

CHRONIC

Chronic exposure to osmium tetroxide can result in accumulation of osmium compounds in the liver 

and kidney and damage to these organs. Osmium tetroxide has been reported to cause reproductive toxicity in 

animals; this substance has not been shown to be carcinogenic or to show reproductive or developmental toxicity in 

humans.  

  

IV. CONTROL MEASURES  

Engineering Controls  

•  Osmium tetroxide solutions must be prepared and handled in a certified chemical hood.    

•  Choose a hood with minimal equipment or obstructions to ensure good containment of vapors. 

•  Working surfaces should be protected with plastic backed absorbent pads to insure containment of any spils.    

•  Post the hood with a warning sign to alert others to the hazards, see warning sign at the end of this SOP.    

•  Ensure that the safety shower and eyewash are operational and access is unblocked . 

  

Administrative Controls  



The laboratory supervisor is responsible to ensure that this procedure is available, understood and adhered to by 

staff using osmium tetroxide in the laboratory.  The MSDS must be readily available and the warning sign should be 

posted where the material is in use or stored.    

  

Personal Protective Equipment   



Lab coat, buttoned and sleeves rolled down, chemically-resistant wrist guards, safety goggles, double Nitrile gloves.  

If working outside a hood, a NOISH approved full-face respirator must be used.  Use of a respirator requires medical 

clearance, training and fit-testing.  Contact EH&S, 4- 8240 for assistance.      

 

V. SAFE USE PROCEDURES  

  

Because of its high acute toxicity and powerful oxidizing ability, osmium tetroxide must be handled in the laboratory 



using prudent practices. In particular, all work with osmium tetroxide must be conducted in a fume hood to prevent 

exposure by inhalation, and personal protective equipment (see section below) must be worn at all times to prevent 

eye and skin contact.  



UCLA
Chemistry
&
Biochemistry

Procedures
for
Safe
Use
of
Osmium
Tetroxide
12/2009




Page
2
of
5

 



Osmium tetroxide should be purchased as a liquid to avoid particulate exposure from the powdered form.  The 

solutions should be stored in labeled tightly sealed containers, and these should be placed in secondary containment.  

Secondary containment should be used anytime the material is transported to another lab location.  

  

When osmium tetroxide is freshly prepared and active, it is colorless to pale yellow in color.  When the material reacts 



and causes oxidation, it turns black.  This is helpful to know especially in the event of a splash or spill (see below) or 

inadvertent dermal exposure (black dots on skin).  

 

A. Training 



1.  Prior to conducting any work with osmium tetroxide, the Principal Investigator must provide training to 

his/her laboratory personnel specific to the hazards involved in working with this substance, work area 

decontamination, and emergency procedures.  

2.  The Principal Investigator must provide his/her laboratory personnel with a copy of this SOP and a copy 

of the osmium tetroxide MSDS provided by the manufacturer.  

3.  The Principal Investigator must ensure that his/her laboratory personnel have attended appropriate 

laboratory safety training or refresher training within the last two years.  

NOTE:  EH&S is available to assist in the education and training of personnel concerning safe work practices. 

 

B. Signage 



When osmium tetroxide is in use, warning signs (ie below and at the end of this SOP) must be posted on the 

chemical hood until the osmium tetroxide has been returned to storage. 

 

 

DANGER 



 

Osmium Tetroxide  

(OsO

4

)  In Use 

Oxidizing Agent 

Severe Irritant 

Causes Eye Damage 

Toxic to Liver and Kidney 

Authorized Personnel Only 

 

 

 

C. Storage 

1.  Pure osmium tetroxide and concentrated solutions should be stored in a location that is secure to 

unauthorized access.  Examples are a locked drawer or cabinet, or a refrigerator within a laboratory that 

is locked when authorized personnel are not present.  A refrigerator containing osmium tetroxide must 

be labeled with a caution sign noting the presence of osmium tetroxide and its hazards.  

2.  Store pure osmium tetroxide and its concentrated solutions in appropriate, sealed glass containers 

within unbreakable secondary containment (i.e., a bottle or vial within a sealed compatible plastic jar or 

metal can with lid). Label all containers, including secondary containment, with the chemical name and 

hazard warning.  

 

D. Handling and Solution Preparation 



1.  When moving pure osmium tetroxide to a chemical hood, do not remove it from the secondary 

containment until it is in the hood. 

2.  Prepare the smallest amount of solution necessary for the procedure, typically 50 mL or less.  Prepare 

the solution volumetrically rather than gravimetrically.  If a balance must be used, weighing must take 

place in the chemical hood. 

3.  Pure osmium tetroxide or its concentrated solutions must be opened only in a chemical hood that has 

been certified within the last 12 months.  Just before use, the operation of the chemical hood must be 

verified by the use of an installed chemical hood monitoring device, a smoke test using a smoke 

generating tube, or a mechanical or electronic device that indicates air flow. During use, the sash must 

be lowered to operating height. 

4.  All lab ware that has contacted osmium tetroxide must be decontaminated by rinsing or dipping in corn 

oil or aqueous solutions of sodium sulfide or sodium sulfite before removing from the hood. 

5.  Immediately after work with osmium tetroxide, decontaminate any spills with kitty litter soaked with corn 

oil. Discard kitty litter as hazardous waste. Or use aqueous solutions of sodium sulfide or sodium sulfite. 




UCLA
Chemistry
&
Biochemistry

Procedures
for
Safe
Use
of
Osmium
Tetroxide
12/2009




Page
3
of
5

 



NOTE: The literature on osmium tetroxide decontamination also mentions using a “mild” solution of sodium 

hydroxide in water.  However, corn oil is recommended for decontamination as it reacts with and thus quenches 

the reactive osmium tetroxide.  Similarly, aqueous solutions of sodium sulfide or sodium sulfite reduce osmium 

tetroxide to less hazardous forms. 

 

E. Personal Protective Equipment 



The following minimum Personal Protective Equipment must be worn during operations with pure osmium 

tetroxide and concentrated solutions:  

1.  Chemical goggles (safety glasses alone are not adequate protection because of osmium tetroxide’s 

severe effects on the eyes). 

2.  Disposable nitrile gloves (NOT latex).  Double-gloving is recommended when working with pure osmium 

tetroxide or concentrated solutions. Change gloves frequently and when contaminated, punctured or 

torn. Wash hands immediately after removing gloves.  

3.  A standard or disposable laboratory coat or disposable coveralls.  A standard laboratory coat may be 

reused before laundering if it has not been contaminated with osmium tetroxide.  If a garment is 

contaminated, remove, place in chemical hood, and decontaminate with corn oil or aqueous solutions of 

sodium sulfide or sodium sulfite before disposing of in hazardous waste or laundering. 

4.  Closed-toed, leather shoes (not fabric or mesh). 

5.  Wash hands thoroughly immediately after working with any concentration of osmium tetroxide. 

 

F. Neutralizing Osmium Tetroxide 



To reduce hazards involved in discarding osmium tetroxide, the following neutralization procedure should be 

employed: 

1.  Perform neutralization in a chemical hood. 

2.  A 2% solution of osmium tetroxide can be fully neutralized by twice its volume of vegetable oil (corn oil 

is preferred because of its high percentage of unsaturated bonds). For every 10 mL of 2% osmium 

textroxide solution, 20 mL of corn oil is required. Pour the corn oil into the osmium tetroxide solution.  

3.  Wait for the oil to completely turn black. 

4.  To test if osmium tetroxide is fully neutralized, hold a piece of filter paper soaked in corn oil over the 

solution. Blackening indicates that osmium tetroxide is still present and more corn oil should be added. 

5.  Aqueous solutions contaminated with osmium tetroxide can be fully neutralized by adding sodium 

sulfide or sodium sulfite to reduce osmium tetroxide to less hazardous forms. 

6.  Dispose of neutralized solutions as hazardous waste.  



 

VI. SPILL GUIDANCE   

In the event of a spill, it is most important to think through an appropriate response to avoid exposure of osmium 

tetroxide to anyone and to avoid further contamination of the location. 

 

Small Spills:

 When the spill is small and manageable, quantity spilled is less than 2 mL, lab personnel will:  

•  Alert personnel in the immediate area. 

•  Isolate the area to prevent the spread of contamination. 

•  Don appropriate PPE (at a minimum use double gloves, buttoned lab coat, safety goggles).   

•  Cover the spill with corn oil-soaked kitty litter.   

•  Scoop the material up and place it in a sealed plastic bag.  

•  Wash the area with aqueous solution of sodium sulfite. 

•  Clean the area with detergent solution. 

•  Remove contaminated PPE carefully and place it in the bag.  

•  Label the bag or container with a completed hazardous chemical waste label/tag and write osmium tetroxide 

clearly on the label.   

•  Arrange with EH&S for pickup and appropriate disposal.  

 

Large Spills:

 When the quantity spilled is greater than 2 mL, lab personnel will:   

•  Advise lab personnel to evacuate the area as soon as possible, without creating panic.  

•  Close all doors leading to lab.  

•  Place OSMIUM TETROXIDE SPILL; DO NOT ENTER sign on the door to inform others of the spill.  

•  Call 911 from a campus phone or 310-825-1491 from a cell phone to request the EH&S Hazmat Team.  

•  Notify the Research Advisor. 

•  Notify the Chemical Safety Officer. 

•  Provide EH&S Hazmat Team with as much information as possible.  

•  Provide EH&S Hazmat Team with corn oil-soaked kitty litter if needed for spill decontamination. 




UCLA
Chemistry
&
Biochemistry

Procedures
for
Safe
Use
of
Osmium
Tetroxide
12/2009




Page
4
of
5

 



Accidental Exposure to Osmium Tetroxide 

•  If osmium tetroxide vapor has been inhaled from a spill, move the victim to fresh air immediately. 

•  If osmium tetroxide has been spilled on skin or clothing, rinse the affected area with water, using a safety 

shower or eyewash, as appropriate, for a minimum of 15 minutes.  During washing, remove contaminated 

clothing.  A disposable laboratory coat or jumpsuit should be available for the exposed individual to wear after 

using a safety shower. 

• 

Notify the Research Advisor. 



• 

Notify the Chemical Safety Officer. 

• 

Seek medical attention as appropriate. 



 

• 

If an ambulance is needed because of injury, call 911 from a campus phone or 310-825-1491 from a cell 



phone. 

 

 



VII. SAFE DISPOSAL PRACTICES  

SOLUTIONS: DO NOT dispose of leftover or spent solutions of osmium tetroxide by emptying into the laboratory 

sink.  Collect solutions and solid osmium tetroxide in a labeled leak proof waste container for pickup and proper 

disposal by EH&S Hazardous Waste Pickup service.  A completed waste label must be attached to the container. 

  

SOLIDS: Collect pipette tips, gloves, ampoules, etc in a rigid leak proof container.  Affix a completed waste label to 



the container.  Due to the toxicity of osmium tetroxide, empty containers must also be collected and disposed as 

hazardous waste.  

 

 

 



 

VIII. REFERENCES

 

 



1) Prudent Practices in the Laboratory: Handling and Disposal of Chemicals (1995) 

http://books.nap.edu/openbook.php?isbn=0309052297&page=364 

 

2) http://www.umdnj.edu/eohssweb/publications/OsmiumTetroxideSOP.pdf 



 

3) http://www.scripps.edu/researchservices/ehs/chemicalsafety/ChemicalAgentSOP/OsmiumTetroxideSOP.pdf 

 

4) Cooper, K. “Neutralization of Osmium Tetroxide in case of accidental spillage and for disposal.” Bulletin of the 



Microscopical Society of Canada 19888, 24-28. 

 

5) Lunn, G.; Sansone, E.B. Osmium Tetroxide. Destruction of Hazardous Chemicals in the Laboratory; Program 



Resources, Inc. Frederick, MD; p 211 - 213. 

 

6) Typical usage: 



 

a) McKee, B. H.; Gilheany, D. G.; Sharpless, K. B. “(R,R)-1,2-Diphenyl-1,2-ethanediol (Stilbene Diol)” Organic 



Syntheses 1998Coll. Vol. 9, 383.  [199270, 47] 

 

b) Herranz, E.; Sharpless, K. B. “Osmium-Catalyzed Vicinal Oxyamination of Olefins by Chloramine-T” 



Organic Syntheses 1990Coll. Vol. 7, 375.  [198361, 85] 

 

 



 

 

 



 

 

 



 


UCLA
Chemistry
&
Biochemistry

Procedures
for
Safe
Use
of
Osmium
Tetroxide
12/2009




Page
5
of
5

 



 

DANGER 

 

 

Osmium Tetroxide  

(OsO

4

)  In Use 

 

Oxidizing Agent 

Severe Irritant 

Causes Eye Damage 

Toxic to Liver and Kidney 

 

Authorized Personnel Only 

 

 



 

Yüklə 55,43 Kb.

Dostları ilə paylaş:




Verilənlər bazası müəlliflik hüququ ilə müdafiə olunur ©genderi.org 2024
rəhbərliyinə müraciət

    Ana səhifə