Politechnika warszawska



Yüklə 7,77 Mb.
səhifə1/10
tarix31.10.2018
ölçüsü7,77 Mb.
#77471
  1   2   3   4   5   6   7   8   9   10

logo_pw_kolorowe_male_300dpi

POLITECHNIKA WARSZAWSKA

WYDZIAŁ
INŻYNIERII MATERIAŁOWEJ












PRACA DYPLOMOWA

MAGISTERSKA




Bartłomiej Wysocki



Właściwości kompozytów NiAl/diament i Ni3Al/diament uzyskanych metodą PPS z udziałem reakcji SHS


The properties of NiAl/diamond and Ni3Al/diamond composites produced by the PPS method with SHS reaction


199567



Promotor: prof. dr hab. inż. Andrzej Michalski

Warszawa, wrzesień 2011




…………………………………..

podpis autora



…………………………………..

podpis promotora






Składam serdeczne podziękowania za cenne uwagi i pomoc przy pisaniu niniejszej pracy prof. dr hab. inż. Andrzejowi Michalskiemu oraz dr inż. Marcinowi Rosińskiemu.



ABSTRACT
In this work there has been investigated the possibility of producing
Ni-Al/diamond composites with SHS (Self-propagating High-temperature Synthesis) reaction carried out in the PPS (Pulse Plasma Sintering) device which was developed by the Group of Phase Transformation in Plasma at the Faculty of Materials Science And Engineering of the Warsaw University of Technology. The PPS method enables obtaining sinters with density close to theoretical in a shorter time and at a lower temperature than those obtained by conventional methods of powder sintering. This work includes results of the research on 6 sinters made in atomic ratio Ni:Al = 1:1, 3:1, 4:1 with and without diamond additive. It was found that the obtained composites have 2-3 times smaller grain size than sinters obtained by known conventional and unconventional methods. It was confirmed that the diamond additive increases hardness from 12% (Ni:Al = 4:1 at.) to 60% (Ni:Al = 1:1 at.) with a slight decrease in density. The study also showed Ni3AlC0.5 and Al4C carbides presence in sinters that testify to the emergence of a strong connection between the matrix and diamond particles.


SPIS TREŚCI





WYDZIAŁ
INŻYNIERII MATERIAŁOWEJ 1


PRACA DYPLOMOWA 1

MAGISTERSKA 1

Bartłomiej Wysocki 1

Właściwości kompozytów NiAl/diament i Ni3Al/diament uzyskanych metodą PPS z udziałem reakcji SHS 1

199567 1

1. WSTĘP 5

2. DOBÓR MATERIAŁU OSNOWY 7

2.1.Wymagania dotyczące osnowy narzędzia metaliczno-diamentowego 7

2.2.Układ Ni-Al 9

2.3.Właściwości NiAl oraz Ni3Al 10

3. DIAMENT 12

3.1.Właściwości diamentu 12

3.2.Zastosowanie diamentu w narzędziach 13

4. WYTWARZANIE KOMPOZYTÓW Ni-Al 15

4.1.Reakcja SHS 15

4.2.Spiekanie niekonwencjonalne metodą PPS 17

4.3.Wytwarzanie kompozytów narzędziowych Ni-Al/diament 19

5. PODSUMOWANIE PRZEGLĄDU LITERATURY 21

6. CEL PRACY 21

7. METODYKA BADAŃ 22

7.1.Przygotowanie mieszanek 22

7.2.Spiekanie metodą PPS 23

7.3.Przygotowanie próbek do badań 25

7.4.Pomiar twardości 27

7.5.Pomiar gęstości 28

7.6.Dyfrakcja rentgenowska 30

7.7.Obserwacje mikroskopowe 30

7.8.Analiza wielkości ziarna 31

8. WYNIKI BADAŃ 32

8.1.Charakterystyka proszków użytych w badaniach 32

8.2.Charakterystyka otrzymanych spieków 36

8.2.1.Twardość 36

8.2.2.Gęstość i porowatość 37

8.2.3.Dyfrakcja rentgenowska 38

8.2.4.Obserwacje mikroskopowe przełomów 43

8.2.5.Analiza obszarowa składu chemicznego 57

8.2.6.Badania metalograficzne i analiza wielkości ziarna 58

9. DYSKUSJA WYNIKÓW 71

10. WNIOSKI 75

11. BIBLIOGRAFIA 76




  1. Yüklə 7,77 Mb.

    Dostları ilə paylaş:
  1   2   3   4   5   6   7   8   9   10




Verilənlər bazası müəlliflik hüququ ilə müdafiə olunur ©genderi.org 2024
rəhbərliyinə müraciət

    Ana səhifə