12
INFO MODE
Figure 14: Set Options Screen
Figure 15: Set Date/Time
ADJ TIME OFF
LOAD MENU ON
EDIT MODE OFF
COOK MORE OFF
NET WORK SETUP
DEMO MODE OFF
1ST OPTIONS SCREEN
AUTO ON OFF
AUTO OFF OFF
R3
R4
L1
L2
L3
L4
SAVE
TEMP 1
SET DATE/TIME
MM/DD/YY HH:MM
<
0
1 /01 /00 14:45 >
AUTO ON TIME
HH:MM
<
05:30 >
AUTO OFF TIME
HH:MM
<
16:00 >
R1
R2
R3
R4
L1
L2
L3
L4
Set Options Screen
From screen 2 of the Info Mode (Figure 13, page
11), press the L2 soft key to access the Set Options
screen (Figure 14). When prompted, enter the
password
9 4 2 8
and press the Enter key.
From the Set Options screen, the following oven
options can be turned on or off:
- “Adjust Time” screen (see Step 6, page 9)
- “Cook More” screen (see Step 9, page 10)
- Edit Mode (page 14 for more details)
- “Load Menu” screen (page 13 for more details)
- Network Setup
- Auto On Enabled/Disabled
- Auto Off Enabled/Disabled
- Demo Mode (TurboChef use only)
Network Setup
From the network setup screen, the following infor-
mation may be entered to configure the oven for
networking:
- IP Address
- Mask
- Gateway (GW)
- Domain Name Server (DNS 1)
- Alternate Domain Name Server (DNS 2)
Each set of numbers may be edited in strings of three
digits:
1. To edit the first string, press the Down key
and then enter the first three digits.
2. Press the Down key again and enter the next
three digits.
3. Repeat until all digits have been entered for
each field.
4. Press “Save.”
If DHCP is turned on (top-left corner of screen),
the oven will automatically be assigned an IP address
when connected to a local area network (if an IP
address is available). In most cases, TurboChef
recommends leaving DHCP off to ensure the IP
address on the oven does not change.
Using Oven Connect (page 4) requires each oven
to be networked. For help determining the correct
network setup information, contact your network
administrator.
Auto On and Off: Setting the Time
From screen 2 of the Info Mode (Figure 13, page
11), press the L4 soft key to access the Set Date/
Time screen (Figure 15). From this screen, the real
time, “auto-on” time, and “auto-off” time can be set.
An accurate real time is critical for using “auto-on”
and “auto-off.” When these features are enabled from
the Set Options screen (Figure 14), the oven auto-
matically turns on and/or off at the specified times.
An accurate date and time also helps ensure the
accuracy of diagnostics and fault condition reporting.
The oven time and date are set at the time of
installation; however, the operator or technician may
at some point be required to make an adjustment.
NOTE: The clock will not automatically update for
Daylight Savings Time.
NOTE: The clock is 24-hour (8:30 p.m. = 20:30).
NOTE: The oven will not retain the date and time
if left unplugged for two or more weeks.
IMPORTANT: For auto-on and auto-off to be
active, they must be enabled from the Set Options
screen (Figure 14).
R1
R2
INFO
MODE
13
To set the real-time date and time,
1. Use the L2 and R2 soft keys (middle left and
middle right) to navigate between digits.
2. Use the
number keys to enter the month, day,
and year, followed by the hour and minute.
3. Select “Save” to save your changes or press the
Back/Stop key to cancel.
To set the auto-on or auto-off time,
1. Ensure the real-time clock is accurate (above).
2. Press the R1 soft key to toggle between
temperatures 1 and 2. If two different temper-
atures are used for cooking, they must be set to
different auto-on and auto-off times.
3. To navigate between digits, use the L3 and R3
soft keys for auto-on time and the L4 and R4
soft keys for auto-off time.
4. Use the number keys to enter the desired hour
and minute for the oven to automatically turn
on or off.
5. Select “Save” to save your changes or press the
Back/Stop key to cancel.
Updating the Oven Menu
NOTE: To update a menu, you may need to verify
that access to the Load Menu screen is turned on.
See the Set Options Screen section on page 12 for
more details.
To load a menu to the oven,
1. Go to screen 2 of the Info Mode (Figure 13,
page 11).
2. Press the R1
soft key to access the Load
Menu screen (Figure 16).
3. Insert the smart card (Figure 17).
4. Press the L1 soft key (Figure 16).
5. Verify the oven beeps and reads FINISHED.
Making a Copy of the Oven Menu
NOTE: To make a copy of the oven menu, you
may need to verify that access to the Load Menu
screen is turned on. See the Set Options Screen
section on page 12 for more details.
To save a copy of the menu to a smart card,
1. Go to screen 2 of the Info Mode (Figure 13,
page 11).
2. Press the R1 soft key to access the Load
Menu screen (Figure 16).
3. Insert the smart card (Figure 17).
4. Press the L2 soft key (Figure 16).
5. Verify the oven beeps and reads FINISHED.
Figure 17: Inserting Smart Card
Smart Card
Smart Card Reader Slot
Figure 16: Loading...Finished
LOAD MENU FROM CARD FINISHED
SAVE TO CARD
R1
R2
R3
R4
L1
L2
L3
L4