Utaa eee department eee 205 Lab. Experiment 6: Study of Flip-Flops Objective



Yüklə 27,02 Kb.
tarix11.10.2017
ölçüsü27,02 Kb.
#4146

UTAA EEE Department

EEE 205 Lab.

Experiment 6: Study of Flip-Flops

Objective:

1. To become familiar with flip-flops.

2. To implement and observe the operation of different flip-flops.

http://pwr.uosiu.info/home/1%20rok%202%20semestr/architektura%20system%ef%bf%bdw%20komputerowych/laborki/spis%20uk%ef%bf%bdad%ef%bf%bdw/flip-flops/7476.gif

Fig.1. Pin Diagram for 74LS76 Fig.2. Pin Diagram for 7404




  1. Pre-Lab.:

  • Explain the difference between latch and flip-flop.

  • What is the difference between 7476 and 74LS76 IC’s?




  1. Overview:

So far you have encountered with combinatorial logic, i.e. circuits for which the output depends only on the inputs. In many instances it is desirable to have the next output depending on the current output. A simple example is a counter, where the next number to be output is determined by the current number stored. Circuits that remember their current output or state are often called sequential logic circuits. Clearly, sequential logic requires the ability to store the current state. In other words, memory is required by sequential logic circuits, which can be created with boolean gates. If you arrange the gates correctly, they will remember an input value. This simple concept is the basis of RAM (random access memory) in computers, and also makes it possible to create a wide variety of other useful circuits.
Memory relies on a concept called feedback. That is, the output of a gate is fed back into the input. The simplest possible feedback circuit using two inverters is shown below (Fig.2):

Fig.2: Simplest realization of feedback circuit


If you follow the feedback path, you can see that if Q happens to be 1 (or 0), it will always be 1 (or 0). Since it's nice to be able to control the circuits we create, this one doesn't have much use -- but it does let you see how feedback works. It turns out that in "real" sequential circuits, you can actually use this sort of simple inverter feedback approach. The memory elements in these circuits are called flip-flops.
1. RS FLIP-FLOP:

RS flip-flop is the simplest possible memory element. It can be constructed from two NAND gates or two NOR gates. Let us understand the operation of the RS flip-flop using NOR Gates as shown below using the truth table for ‘A NOR B’ gate. The inputs R and S are referred to as the Reset and Set inputs, respectively. The outputs Q and Q' are complements of each other and are referred to as the normal and complement outputs, respectively. The binary state of the flip-flop is taken to be the value of the normal output. When Q=1 and Q'=0, it is in the set state (or 1-state). When Q=0 and Q'=1, it is in the reset/clear state (or 0-state).


Fig.3. Circuit Diagram of RS Flip-Flop



  • S=1 and R=0: The output of the bottom NOR gate is equal to zero, Q'=0. Hence both inputs

to the top NOR gate are equal to 0, thus, Q=1. Hence, the input combination S=1 and R=0 leads to the flip-flop being set to Q=1.

  • S=0 and R=1: Similar to the arguments above, the outputs become Q=0 and Q'=1. We say

that the flip-flop is reset.


  • S=0 and R=0: Assume the flip-flop was previously in set (S=1 and R=0) condition. Now

changing S to 0 results Q' still at 0 and Q=1. Similarly, when the flip-flop was previously in a reset state (S=0 and R=1), the outputs do not change. Therefore, with inputs S=0 and R=0, the flip-flop holds its state.

  • S=1 and R=1: This condition violates the fact that both outputs are complements of each

other since each of them tries to go to 0, which is not a stable configuration. It is impossible to predict which output will go to 1 and which will stay at 0. In normal operation this condition must be avoided by making sure that 1's are not applied to both inputs simultaneously, thus making it one of the main disadvantages of RS flip-flop.

All the above conditions are summarized in the characteristic table below:



Characteristic Table:



2. JK FLIP-FLOP:

The JK flip flop (JK means Jack Kilby, a Texas instrument engineer, who invented it) is the most versatile flip-flop, and the most commonly used flip flop. Like the RS flip-flop, it has two data inputs, J and K, and an EN/clock pulse input (CP). Note that in the following circuit diagram NAND gates are used instead of NOR gates. It has no undefined states, however. The fundamental difference of this device is the feedback paths to the AND gates of the input, i.e. Q is AND-ed with K and CP and Q’ with J and CP.


Fig.4. Circuit Diagram and Characteristic Table of JK Flip-Flop

The JK flip-flop has the following characteristics:


  • If one input (J or K) is at logic 0, and the other is at logic 1, then the output is set or reset (by J

and K respectively), just like the RS flip-flop.

again like the RS flip flop. CP has no effect on the output.

  • If both inputs are high, however the flip-flop changes state whenever a clock pulse occurs; i.e.,

the clock pulse toggles the flip-flop again and again until the CP goes back to 0 as shown in the shaded rows of the characteristic table above. Since this condition is undesirable, it should be eliminated by an improvised form of this flip-flop as discussed in the next section.
3. MASTER-SLAVE JK FLIP-FLOP:

Although JK flip-flop is an improvement on the clocked SR flip-flop it still suffers from timing problems called "race" if the output Q changes state before the timing pulse of the clock input has time to go "OFF", so the timing pulse period (T) must be kept as short as possible (high frequency). As this is sometimes not possible with modern TTL IC's the much improved Master-Slave J-K Flip-Flop was developed. This eliminates all the timing problems by using two SR flip-flops connected together in series, one for the "Master" circuit, which triggers on the leading edge of the clock pulse and the other, the "Slave" circuit, which triggers on the falling edge of the clock pulse.


The master-slave JK flip flop consists of two flip flops arranged so that when the clock pulse enables the first, or master, it disables the second, or slave. When the clock changes state again (i.e., on its falling edge) the output of the master latch is transferred to the slave latch. Again, toggling is accomplished by the connection of the output with the input AND gates.

Fig.5. Circuit Diagram of Master-Slave JK Flip-Flop





Characteristic Table:

  1. Laboratory Work:

a) In the Lab, Build the RS latch shown in Fig.6. Use switches as a bouncing switch. Q and Q’ Outputs are connected to LED’s. Verify the truth table experimentally.

http://api.ning.com/files/4o3hlltj*6fosqftjg7gpgmmcrohpueuw7zq*8jbzlr8geyrfmpebioeon0cgkqyzdktrt9rfaen67zllgswfvv5ly2q3zwb/logicgatenorus.png

http://api.ning.com/files/4o3hlltj*6fosqftjg7gpgmmcrohpueuw7zq*8jbzlr8geyrfmpebioeon0cgkqyzdktrt9rfaen67zllgswfvv5ly2q3zwb/logicgatenorus.png

Fig.6. RS Latch Circuit.



b) In the Lab, Construct the circuit of Fig 8. Look at the data sheet for the 74LS76 and determine the inactive logic required at the PRE and CLR inputs.
http://www.ece.unm.edu/vhdl/old_labs/foundation_labs/lab_5/4_15.jpg

http://www.ece.unm.edu/vhdl/old_labs/foundation_labs/lab_5/4_15.jpg

Fig.7. Function Tables For 7476 & 74LS76




Fig.8. JK Flip-Flop Circuit

Write your observations and comments under the steps.


  • Connect the 74LS76 for the SET mode by connecting J = 1, K = 0. With CLOCK (CP) = 0;

test the effect of PRE, CLR by putting a 0 on each, one at a time.


  • Put CLR = 0, then pulse the clock (CP) by putting a HIGH then a LOW, on the clock. Does

the CLR input override J input?

  • Verify the operation of the JK flip flop by experimentally obtaining the characteristic table.




  • Determine whether the flip-flop you are using a positive pulse-triggered or a negative edge

triggered?

http://pwr.uosiu.info/home/1%20rok%202%20semestr/architektura%20system%ef%bf%bdw%20komputerowych/laborki/spis%20uk%ef%bf%bdad%ef%bf%bdw/flip-flops/7476.gif

Fig.9. Pin Diagram of 74LS76



NAME: ST.NUMBER:

4. Post Lab. Questions:

Q.1.) Sketch the waveform of for the 7476 and 74LS6 negative edge-triggered JK flip-flop with the input waveforms given.








c:\users\tayfun okan\desktop\20131216100741408.tif








http://www.ustudy.in/imagebrowser/view/image/4452/_original













http://www.ustudy.in/imagebrowser/view/image/4452/_original


Yüklə 27,02 Kb.

Dostları ilə paylaş:




Verilənlər bazası müəlliflik hüququ ilə müdafiə olunur ©genderi.org 2024
rəhbərliyinə müraciət

    Ana səhifə