Mipa Struktur-Additiv fein
Technical data sheet
Page 1 / 2
Intended use
Mipa Struktur-Additiv fein is an additive for Mipa OC-, AC-, PUR- and PUR HS-paints as well as for Mipa 2K clearcoats
to create textured elastic 2K paints. Especially suitable to paint slightly textured vehicle plastic parts like bumpers or
exterior mirrors.
Mixing ratio:
Mipa OC-/AC-/PUR-/PUR HS-paints/2K-clearcoats + Mipa Struktur-Additiv 1 : 1 by weight
Then add the hardener as mentioned in the technical data sheet of the base paint.
Spreading rate: --
Processing instructions
Colour
colourless
Mixing ratio
Hardener
by weight (lacquer : hardener)
by volume (lacquer : hardener)
see technical data sheet of base
paint
--
--
Hardener
for complete paintwork
for partial paintwork
--
--
Pot life
see technical data sheet of base paint
Thinner
see technical data sheet of base paint
Spray viscosity
see technical data sheet of base paint
gravity spray gun
Airmix/Airless
--
--
Application mode
Application mode
Hardener
pressure
(bar)
nozzle (mm) spray
passes
Thinner
gravity spray gun (high
pressure)
--
2 - 2,5
1,3 - 1,6
2 - 3
--
HVLP (low pressure)
--
2 - 2,2
1,3 - 1,6
2 - 3
--
HVLP/ internal nozzle
pressure
--
0,7
--
--
--
MIPA SE · Am Oberen Moos 1 · D-84051 Essenbach · Tel.: +49(0)87 03/922-0 · Fax: +49(0)87 03/922-100 · mipa@mipa-paints.com · www.mipa-paints.com
This technical data sheet is supplied for informational purposes only! According to our information, all data and recommendations correspond to the state of art and are based on
years of experience in manufacturing our products. They do not exempt the user from his obligation to verify professionally, on his own responsibility, the suitability of our
products to the intended purpose under prevailing conditions. Safety data sheets and warnings on packaging must be observed. We reserve the right to modify and to complete
the information content at any time, without prior notice or obligation to update.
Version: en 0917
Mipa Struktur-Additiv fein
Technical data sheet
Page 2 / 2
Flash-off time
5 - 8 min between coats
10 - 15 min before oven drying
Dry coat thickness
50 - 60 µm
Drying time
object
temperature
dust dry
set to
touch
ready for
assembly
sandable
recoatable
see technical data
sheet of base paint
--
--
--
--
--
Note
Storage:
at least 3 years in unopened original container.
VOC Regulation :
--
Processing conditions:
from +10°C and up to 80% relative humidity. Ensure adequate air ventilation.
Processing instructions:
--
MIPA SE · Am Oberen Moos 1 · D-84051 Essenbach · Tel.: +49(0)87 03/922-0 · Fax: +49(0)87 03/922-100 · mipa@mipa-paints.com · www.mipa-paints.com
This technical data sheet is supplied for informational purposes only! According to our information, all data and recommendations correspond to the state of art and are based on
years of experience in manufacturing our products. They do not exempt the user from his obligation to verify professionally, on his own responsibility, the suitability of our
products to the intended purpose under prevailing conditions. Safety data sheets and warnings on packaging must be observed. We reserve the right to modify and to complete
the information content at any time, without prior notice or obligation to update.
Version: en 0917