Using Effects
62
input settings of the KROSS in G-SET (Use
Global
Settings), or use the individual parameters of each mode to
specify the BUS or Send settings. (see “Effect settings for
audio input” on page 65)
Depending on the type of effects that you’re using on
the external audio input, and on their settings, it is
possible for feedback to occur. If this occurs, adjust the
input/output levels and the effect settings. Take special
care when using high-gain effects.
Audio recorder
The audio recorder can record the sound as it is processed by
the effects
specified in Program, Combination, or Sequencer
mode.
You can’t apply effects to the playback of the audio
recorder.
Routing and effect settings
Routing lets you specify how each sound will be connected
to the various effects. In each mode,
you can adjust settings
for the program’s oscillators, the combination’s timbres, and
the song’s tracks.
Here we’ll explain how to adjust routing settings in each
mode, and how to edit the effect settings.
Effect settings for a program
Routing
1. Access the P-FX ROUTING> BUS page.
2. “Bus (Bus Select)” specifies the bus where the output
from the oscillators will be sent. Here we’ll choose
IFX1 so that the output of the oscillators will be sent
to insert effect 1.
L/R: The oscillator output will not be sent to an insert
effect. It will pass through the total effect, and then be
sent to OUTPUT L/MONO and R.
IFX1–IFX5: The oscillator output
will be sent to insert
effect 1–5.
Off: The oscillator output will not be sent to OUTPUT L/
MONO or R, or to insert effects 1–5. Choose this if you
want to send the sound directly to the master effects at the
send levels specified by Send1 (to MFX1) or Send2 (to
MFX2) (P-FX ROUTING> SEND page).
3. If you selected L/R or Off in step 2, you can use each
oscillator’s Send1 (to MFX1) and Send2 (to MFX2)
parameters to set the send levels to the master effects.
Adjust these settings in the P-FX ROUTING> SEND
page.
If Bus (Bus Select) is set to IFX1–5, the send levels from
the output of each insert effect to the master effects are
specified by the S1 (Send1) and S2 (Send2) parameters
(P-Fx Routing Mixer page). (see step 6 of the next
section, “Insert effects”)
4. “FX Control Bus” sends the output of oscillators 1
and 2 to the FX control bus.
Use this when you want to use a different sound to
control the sound that’s being input to an effect. You can
use two FX control buses to freely control the sound. (see
“FX Control Bus” on page 199 of the Parameter Guide)
Oscillator1
Filter1
Amplifier1
Oscillator2
Audio
Recorder
Filter2
Amplifier2
Return
OUTPUT
L/MONO, R
Send
REC
PLAY
Mic In (mono)
Line In (stereo)
Insert
Effect 1–5
Master
Effect 1, 2
Routing and effect settings
Effect settings for a program
63
Insert effects
1. Access the P-FX ROUTING> IFX page.
2. In the Effect area, select each insert effect that you
want to use.
You can press the ENTER button and choose from a list.
Tip: You can use the “Copy Insert Effect” function to
copy the effect settings from another effect. The “Swap
Insert Effect” function lets you exchange (for example)
insert effects 1 and 5.
3. In the Effect On/Off area, turn the insert effect on.
Each time you press the ENTER button, the insert effect
will turn on or off. If this is Off,
the result will be the
same as if 000: No Effect is selected; the input sound will
be output without change.
4. Specify the chain setting.
If the
Chain check box is selected, the insert effect will
be chained in series. Set the
Chain To parameter to
“→2.”
If →2 is selected, the insert effects will be
connected in
series in the order of IFX1 → IFX2.
5. Access the P-FX ROUTING> MIXER page.
6. Set the “Pan:#8,” “Bus (Bus Select),” “FX Control
Bus,” “Send1,” and “Send2” parameters to specify the
pan and routing of the signal following the insert
effect.
If
Chain is On, the settings that follow the last insert
effect will be used. (
FX Control Bus is an exception.)
Pan: #8: Specifies the pan.
Bus (Bus Select): Specifies the output destination.
Normally you’ll set this to L/R.
Send1, Send2: Specify the send levels to the master
effects. For this example, set them to 127.
FX Control Bus: The sound
that has passed through the
insert effect is then sent to the FX control bus. This
allows you to use a different sound to control the input to
an effect. You can use two FX control buses, giving you a
wide range of possibilities for controlling the effects. (see
“FX Control Bus” on page 199 of the Parameter Guide)
7. In the P-FX ROUTING> IFX page, edit the
parameters of the insert effect you selected.
Edit the parameters in the P-IFX> IFX 1–5 pages.
Effect On/Off: Turns the insert effect on/off. This is
linked with the on/off setting of the P-FX ROUTING>
IFX page.
For details on the parameters of each effect, please see
page 207 and following of the Parameter Guide.
Double-size effects
Double-size effects (D00: St.Mltband Limiter–D13: Early
Reflections) use twice as much processing
area as other
effects.
D00: St.Mltband Limiter–D10: Rotary SpeakerOD can be
used with insert effect 1, D00: St.Mltband Limiter–D09:
Vocoder can be used with insert effects 2–4, and D00:
St.Mltband Limiter–D13: Early Reflections can be used with
master effect 1.
When you use a double-size effect, the next-numbered effect
will be unavailable. For example if you’ve selected a double-
size effect for IFX1, you won’t be able to use IFX2.
Example of when a double-size effect is selected for IFX1
Master effects
1. “Send1” and “Send2” settings (P-FX ROUTING>
SEND page or P-FX ROUTUNG> MIXER page)
determine the input level to the master effects. If
“Send1” and “Send2” are set to 0, nothing will be
input to the master effects. “Send1” corresponds to
MFX1, and “Send2” corresponds to MFX2.
2. Access the P-MFX> SETUP page.
Effect On/Off
Effect
Chain Chain To
Pan:#8
Bus
Send1
Send2
FX Control Bus
Effect Parameters
Effect On/Off
Wet/Dry
