Keyboard-Functions
In the Basic-Menu when a message is displayed, you can acknowledge this message and switch off the horn by pressing any key.
From the Basic-Menu (the menu on the display after being switch on) you can select different Sub-Menus by pressing the key 1 to 9. In the Sub-Menus you can jump from one value to the other by pressing “#”. The flashing Cursor indicates which value is active for Input. So if you input wrong data, press “#” several times until you come again to the desired value. In Menu 1 (Universal-channel) you can go back one Input-field also by key “*”.
If you changed the value you can go directly back to Basic-Menu without pressing “#”
Go back or return from the Submenu by pressing “*”. From Menu 1 (Universal-channel) you return by pressing “*” twice.
After switching the device on you see the Basic-Menu. You can switch the values displayed in here with the Program-Switch in the middle of the Metamorphosis
You have the following options:
-
Position 1: Battery-Voltage, Solar-Current, Battery-Voltage as a graphical bar
-
Position 2: Battery-Voltage, Solar-Current, Solar-Currrent as a graphical bar
-
Position 3: Battery-Voltage, Load-Current 1 (Load 1+2) and Load-Current 2 (Load 3-5) and Load Current 3 (external Load). Load 1+2 as a graphical Bar
-
Position 4: Battery-Voltage, Solar Ah/day and Ah Totalizer. You can reset the Totalizer by pressing ”0”
-
Position 5: Battery-Voltage, Load Ah/day and Ah Totalizer. You can reset the Totalizer by pressing ”0”
-
Position 6: Battery-Voltage, Output Solar in Watt, Output Load in Watt
-
Position 7: Ah Solar und Ah Solar / day.. You can reset the values by pressing ”0”
-
Position 8: Ah Load 1 (Load 1+2), Ah Load 2 (Load 3-5), Ah Load 3 (external for example from Inverter), Ah Load Total . Second Line: Ah Load Total / day. You can reset the values by pressing ”0”
-
Position 9: Minimal, maximal Voltage / day. You can reset the values by pressing ”0”
-
Position 10: KWh from external Energy-Counter if connected. You can reset the values by pressing ”0”
Voltage of NimH-Batteries if connected. Temperature and Time.
-
Position 11: State of Charge and active Battery-Bank. Here you can switch over manually the Battery-Bank with key "#" and then select the Battery-Bank-number 1-3. Finish with key "*" or switch over Program-Switch.
-
Position 12: Radio-Sensors if they are connected
Note: The flashing”*” in the first line indicates that the Solar-charging is active.
A stem cell is most fascinating! The cell can realize different functions and tasks, depending on which is activated. Simultaneously it is in close contact with other cells and communicates intensive.
The universal module "Soft Cell" works a bit in the same way. It can take realize different tasks, includes the most important basic functions and is in close contact with the other modules to exchange information. All modules have the same structure.
Background: Individualized software is very expensive and often not very flexible for necessary changes or adjustments. To save costs and to give customers more flexibility and transparency, this universal module "Soft Cell" was created. It is thus possible by an excel sheet to realize a variety of different functions without the need to program it.
Here you do have a Multi-Purpose-Function for up to 20 different Modules.
Hint: In the Appendix you find an Excel-Sheet for to make the planning more easily. You find it on the CD or in the Internet.
In Menu 8 Parameter 27 you setup the number of Channels used. This value should correspond to the number of values you are using for better Performance!
In the Menu Universal Modules you can jump one Input-field back with key „*“. If you wait a little bit and press „*“ again, then jump to the next field back. Two times key „*“ (without break) jumps back to the main Menu.
Timer: Device switched Time-controlled (f.e. fridge only at daytime, light only at night etc).
Start once for a defined Time: You just setup the running-time of the Timer and then switch the channel on. The Output is active just once for the defined time. After that the channel is switched off.
Pulses: Device switched with Pulses. Every minute for 10 seconds or every Monday for 3 hours etc. For example for a generator start etc.
The above Time -Function can be combined with all other functions.
Simulation of absence: Often Solar-Systems are installed where people are often absent. You can program a Timer to switch on lights for to simulate the Presence of somebody
Load-shedding: Different Loads can be switched off depending from the Battery-Level. With delay switch on and delay switch off (minimum run-time). With Hysteresis (Difference-value between on and off).This can be used for Load-shedding of the Devices connected. First the less important, then the critical ones. Example: Channel 1-5
Voltage-Control: Switch on devices if the battery is full etc. For example for to use all Power of the Solar-Panels to switch a Water-Pump etc. With delay on/off and Hysteresis.
Output Delayed off: for example to switch on a light by a switch and turn off automatic to save Power. The Start can be by a Push-Button or a Switch.
Example: Channel 7-11;
Alarm-Messages and Action: For example if any Value (Voltage, Temperature) is inside a critical range a Alarm can be activated and / or a Telephone-call, SMS etc. Example: Channel 6, Battery empty
Alarm-System: Using moving-Detectors etc. or door-switches (in the cabinet etc) you can build up a Alarm-System for to protect your equipment. Alarm can be by a Siren or a Telephone-call or a SMS if you have a Mobile-Phone connected. Example: Channel 7-11
Cooling: For example the solar panel. You can Input the Temperature-Setpoint with Hysteresis and Pulses for the cooling-pump. Example: channel 12
Heating: For example a glass-house if it may not get too cold. With Temperature-Setpoint and Hysteresis.
Level-Control with analog Sensors: for example for the Tank of the cooling water.
Level-Control with 1 or 2 digital Sensors: for example refill for a certain time if the empty Level is coming.
Interlock with an Input: Pump only active if no empty-Level.
Interlock with an Output: Dosing only active if the Pump is running.
Difference-Regulation: For example for Solar-thermal Systems for the Temperature-Difference-Regulation
Activating Channel by SMS
If you send a SMS with the Text Meta81 or Meta91 to the Metamorphosis, you can activate a Universal-channel by selecting Input 90 (for SMS with the Text Meta81) or 91 (for SMS with the Text Meta91). If all conditions are ok and you send the SMS the output will be switched on. By Sending the SMS with the Text Meta80 or Meta90 the Module is deactivated again
In each Module you can define two Inputs and two Outputs. Inputs can be analog or digital, Outputs Relais or Transistor or virtual, to be used in other Modules. Or it can be a Telephone-notification.
Dostları ilə paylaş: |
