Anschluss der Gerät

Menu 4: Load-Shedding off for Emergency

In order to have a Emergency-light although the batteries are empty, you can activate a Emergency Load-Shutting Temporarily off. Now the Output will be active for a dedicated Time although the batteries are empty.

But be aware that batteries get seriously damaged if they are excessively deep-discharged.

Press ”1” for to activate this function and 0 for to deactivate it.

This Function can be activated by an external Switch (Input 3) as well.

Menu 5: Input and Test of Telephone-numbers

For to use this function you need to have a GSM-Modem or a Mobile phone connected.

You can enter two telephone-numbers in here. These numbers are dialed in case of Alarm.

First you select which Telephone number you want to Input (1-2). Press ”#” to jump to the Input-field of the Telephone-number. You can enter a 12 digit number now. If you want to enter the next Telephone-number press ”#” again, select Nr.2, press ”#” and enter the number in the Input-field.

If you want to test it, press ”#” and select ”1” at the Test-field.

If you want to have all numbers being dialed subsequently enter ”12” for the Number-Selection and leave the Sub-Menu.

If you want to have only one specific number being dialed, enter the desired number (1-2) in the field for the Number-Selection and leave the Sub-Menu.

To have no call enter key “0” at Number Input.

Depending of Parameter 5 in Menu 8 a Telephone-call is initiated or a SMS is activated,

To cancel a call enter the key “*”.

Menu 6: Tracking on/off, Input of the Tracking-Time and Start/End-Time

If you have a mechanical construction that lets your Solar-Panel follow the sun position in one or two axis, you can use this automatic for to get it turn. The benefit from letting the Solar-Panel follow the sun position in one axis is up to 30%!

General: Tracking is realized by a Formula for the X-Axis (Horizontal) and by a Table for the Y-Axis (vertical).

You have a Switch for to activate it in Menu 6.

And the time for Start and End Solar Tracking (SR/SS).

The Tracking-Increments are calculated by: Tracking-Time Total / number of Increments (Time between SR and SS)+ Slip (Menu 8, Parameter 37). All 30 minutes there is a Tracking. At the End-Time (SS) + 2 hours the Unit is going back to Basic-Position for max. Tracking-Time + Time Rotate back (Menu 8, Parameter 38) or till the Final Switch (see wiring diagram) is 1-Signal.
Following Parameters are relevant:

on: Here you activate this function ”Solar tracking” with key ”1”. The Motor is activated every half an hour for a specific time. And in the evening the Motor is switched on reverse for to go back to the Base-position. This Position can be detected by a final-switch (see the Appendix for the electrical wiring).

SR (Sun Raise): Here you enter the hour for Sunrise.

SS (Sun Set): Here you enter the hour for Sunset (for example 19 for 19 o’clock). From Time to time you can readjust these values

Time: This is the Tracking-Time. In here you enter the value how long it takes for the Tracking-Unit to go from Base-Position to the Final-Position. You can figure out this value by going to Manual-Mode (Menu 9) and switch the Motor on manually (R6 on) and measure the time for a complete turn from beginning to the End. This value (in seconds) you have to enter in here.

In Menu 8, Parameter 37: Rotate Slip: Here you enter the delay for every starting at Tracking (about 3 sec).

In Menu 8, Parameter 38: Time Rot.back: Here you enter the additional Time (Tracking-Time + X) it takes for to go back in Base-Position. But this is the Max-Time! Going back to Basic-Position should be stopped by a Proximity-Switch (Signal 1) at Input 1 (Terminal 47+48). If no Proximity-Switch is coming, it stops with this time and a Error-Message is generated

If you do not have the correct tracking in the horizontal direction correct the rotate time in Menu 6

For Horizontal Tracking Relay 5, 6 is used and can not be used for any other purpose (Generator, Alarm etc.)
In Menu 8, Parameter 36 you can also activate a vertical Tracking. This runs according to a Table. In this case Relay 3, 4 is used and can not be used for any other purpose (Generator, Alarm etc.).

If you do not have the correct tracking in the vertical direction correct Menu 8, Parameter 39

Menu 7a: Input of Date and Time

For the Protocol, the Timer and the Tracking-Function you have to enter Data and Time in here. The fields are month.day, hour:minutes and you jump from one field to the other with the key ”#”.

You can also input the Week-day in here. Monday could be Number 1.

Note that the Time is Reset when you switch off the Metamorphosis.

Menu 7b: Output Voltage

Here you see the Value of the Output-Voltage coming from the integrated optional Voltage-Regulator. You can adjust this Voltage with the right Regulator next to the Program-Switch. This voltage can be used for to connect small appliances like Walkman, CD-Player etc. to the Metamorphosis. The Output-Range is 3-12V with up to 2A.

Be careful not to change the voltage when a device is already connected. Overvoltage can destroy the Device! (see the Appendix for the electrical wiring).
Here you have for testing purposes more Displays depending from the Program-Switch:
PWM-Value (Solar)

Slow Switch (on-Time per Minute for Solar)

Boost-Ch. (Pulses)

Ma I2C PWM (Bus Master-Value)

SL I2C PWM (Slave values)

Menu 8: Settings

In this Submenu you can change a lot of different parameters and values if you are not satisfied with the Pre-settings. First you select the Number of the Value (see list below). Then you press ”#” and you can enter the according value. The next value is selected by simply pressing ”0” in the field of the Parameter-Number or by entering the desired Parameter-number. That means with just pressing ”0” at Parameter-Nr you can scroll through all the values.

You can also reset it to the Factory-Settings by Parameter 70.

Following Parameters can be changed: