Forma Laboratory Refrigerators 34830H63 Rev. A a & d voltages
Thermo Scientific Forma Laboratory Refrigerators
Yüklə 0,98 Mb. Pdf görüntüsü
|
8 Thermo Scientific Forma Laboratory Refrigerators Installation and Operation 9 Chart Recorders Panel-mounted six inch recorders are available as options on all models. Recorder operation begins when the system is powered on.
9.1 Set Up and Operation To prepare the recorder to function properly, complete the following steps: 1. Open the recorder door to access the recorder. 2. Connect the nine volt DC battery located at the recorder’s upper right corner. This battery provides back-up power. 3. Install clean chart paper (refer to Section 9.3 below). 4. Remove the plastic cap from the pen stylus and close the recorder door.
The recorder normally uses AC power when the system is operating. If AC power fails, the LED indicator flashes to alert you to a power failure. The recorder continues sensing cabinet temperature and the chart continues turning for approximately 24 hours with back-up power provided by the nine-volt battery. The LED indicator glows continuously when main power is functioning and the battery is charged. When the battery is low, the LED flashes to indicate that the battery needs to be changed. 9.3 Changing Chart Paper To change the chart paper, complete the following steps: 1. Locate the pressure sensitive buttons at the front, upper left of the recorder panel. 2. Press and hold the change chart button for one second. The pen will move off the scale. 3. Unscrew the center nut, remove the old chart paper, and install new chart paper. Carefully align the day and time with the reference mark on the recorder panel (a small groove on the left side of the panel, shown in Figure 4). 4. Replace the center nut and hand tighten. Press the change chart button again to resume temperature recording. 9.4 Calibration Adjustment This recorder has been accurately calibrated at the factory and retains calibration even during power interruptions. If required, however, adjustments can be made as follows: 1. Run the unit continuously at the control setpoint temperature. Continue steady operation for at least two hours to provide adequate time for recorder response. 2. Measure cabinet center solution temperature with a calibrated temperature monitor. (Solution temperature is measured inside the sensor bottle.) 3. Compare the recorder temperature to the solution temperature. If necessary, adjust recorder by pressing the left (#1) and right (#2) chart buttons.
9 Volt Battery Imprinting Stylus
Hub-Nut and Retaining Wire Chart Chart Buttons 1 2 3 CHANGE CHART 9 Thermo Scientific Forma Laboratory Refrigerators Installation and Operation 10 Maintenance 10.1 Cleaning the Drawers and Cabinet Interior Pharmacy refrigerators come standard with drawers. All other refrigerators come standard with wire shelves. Additional drawers and/or shelves are offered as available options. To clean the drawers and cabinet interior, remove the drawers following the instructions below. Use a solution of water and a mild detergent. Rinse the drawers and wipe them dry with a soft cloth.
10.2 Removing the Drawers The drawers in all models can be removed for cleaning. To remove the drawers, complete the following steps (refer to Figure 6): 1. Pull the drawer toward you until the slide is fully extended. 2. Lift the back of the drawer to disengage the mounting tab from the slot on the slide. 3. Raise the back of the drawer almost to a vertical position and disengage the front mounting clips from the slide. The drawer slides are adjustable. You can position these slides in the vertical slots which are spaced at one-inch intervals.
To reinstall the drawers, complete the following steps: 1. Pull both drawer slides toward you until the slides are fully extended. 2. Position the drawer between the slides and insert the front mounting clips into the slots on front of the slides. 3. Push the back of the drawer down between the slides and insert the drawer tabs into the back slots. Note: The drawers fit snugly between the slides. Push on the back of the drawer from the inside to insert the drawer tabs completely into the slots. Make sure both drawer tabs are aligned with the slots on the slides before pushing the drawer down between the slides. 10.4 Cleaning the Condenser WARNING! Disconnect equipment from main power before attempting any maintenance to equipment or its controls. CAUTION! Condensers should be cleaned at least every six months. In heavy traffic areas, condensers load with dirt more quickly. Failure to keep the condenser clean can result in equipment warm-up or erratic temperatures. Periodically check the condenser to make sure that it is clean. In all models except for the 45 ft 3 sliding glass door model, the condenser is located in the top machine compartment. To clean the condenser: 1. Disconnect the power. 2. Remove the top grill (bottom front grill if you have a sliding glass door model). 3. Use a vacuum cleaner with hose and brush attachments to clean the front face of the finned surface. 4. Clean up any loose dust and replace the grill. 5. Reconnect the power. Tabs
Drawer slide Slot
10 Thermo Scientific Forma Laboratory Refrigerators Installation and Operation 11 Troubleshooting WARNING! Troubleshooting procedures involve working with high voltages which can cause injury or death. Troubleshooting should only be performed by trained personnel. This section is a guide to troubleshooting equipment problems. Table 6. Troubleshooting Procedures Problem Cause Solution Unit does not operate or Power Failure Indicator is on. Power supply 1. Check that the cord is securely plugged-in. 2. Plug another appliance into the outlet to see if it is live. 3. If the outlet is dead, check the circuit breaker or fuses. Temperature fluctuates. Cold control Make sure that the cold control is set correctly. Refer to Section 7.1 on page 6. Condenser Make sure the condenser is clean. Refer to Section 10.4 on page 9. High pressure Check the system high-pressure cut-out button. This is an encapsulated control with a rubber boot over the reset button. To reset the control, push it down; use a blunt instrument to avoid tearing the boot.
Unit warms up. Door is open. Make sure the door is completely closed. Warm product recently loaded in unit. Allow ample time to recover from loading warm product. Power supply Check for proper voltage to the unit. If there is no voltage to the unit, call an electrician. Compressor 1. If the compressor is not running, check if the unit has a power failure alarm. If the power failure alarm light is on, have an electrician check for proper voltage to the unit. 2. If the compressor is running, open the door and look through the slotted air intake in the bottom of the evaporator cover to see if icing is present on the evaporator. If icing is present and there is no air flow behind evaporator, call technical service for assistance. The evaporator fans may be inoperative. 3. If the compressor is running and there is airflow behind the evaporator, contact an authorized service provider or call the technical support hot line for assistance.
11 Thermo Scientific Forma Laboratory Refrigerators Installation and Operation 12 Accessories Alarm Systems Special Voltages Standard voltages are listed under Voltage in Specification Charts associated with each product category. Standard voltages are available at no charge; alternative voltages may be available at an extra charge. All voltages must be specified when ordering. Contact Customer Sales for more information. Low Voltage Protection Temperature Recorders All six inch recorders utilize pressure-sensitive chart paper (1 box @ 50 charts included); no inking is required..
Optional stainless steel drawers are offered as an alternative to standard shelving.
signal in the event of temperature rise or power failure. Adaptable to telephone switchboard. Can be located up to 1/3 mile (1760 ft/536 m) from cabinet. Must be used with electronic alarm system and connected to normally-open or normally-closed remote alarm contacts. Wire not included. Specify voltage when ordering. 5612 Deluxe Electronic Remote Alarm System. User programmable to sound alarm in the event of temperature rise or power failure. Can dial up to four telephone numbers to advise of alarm condition across any telephone system which accepts pulse dialing. One System can monitor up to four individual cabinets. In addition, the System can monitor up to three groups of cabinets. Contact Customer Sales for detailed specifications. Customer installed.
equipment from damage by boosting low voltage automatically. Provided with terminal board for direct wiring. Field installed. Specify voltage when ordering. 5575 Description Catalog No. Temperature recorder, 6 in. circular chart, seven-day drive, panel mounted. Factory installed. Specify when ordering. 6183-7 Temperature recorder, 6 in. circular chart, seven-day drive, free-standing, for all refrigerator models. Customer installed. Specify voltage when ordering. 6383-7 Description Catalog No. Chart paper, package of 50, for six inch, seven-day recorder, -40°C to +25°C.
locking, 3 in. diameter, for 11.5, 23.3, 29.2, 51.1, and 78.8 cu.ft models only.
Zinc Plated. Full Size. For use with 23.3, 45.8, 51.5, and 78.8 cu.ft models only
Zinc Plated. Half size. For use with 23.3, 45.8, 51.5, and 78.8 cu.ft models only.
Zinc Plated. Full size. For use with 29.2 cu.ft models only. 6695 Zinc Plated. Half size. For use with 29.2 cu.ft models only. 6697 Zinc Plated. Full size. For use with 11.5 cu.ft models only. 6202 Zinc Plated. For use with 4.9 cu.ft models only. 7128 Description Catalog No. For 4.9 cu.ft Undercounter Models For REL-404, roll-out drawer assembly, two drawers. 7129 For 11.5 cu.ft Space Saver Models For REL-1204, roll-out drawer assembly, five drawers. 6599 For 23.3, 51.1, and 78.8 cu.ft Models For REL-2304, roll-out drawer assembly, six drawers, full adjustable, fully extendable.
For REL-5004, roll-out drawer assembly, 12 drawers, fully adjustable, fully extendable.
For REL-7504, roll-out drawer assembly, 18 drawers, fully adjustable, fully extendable.
Additional stainless steel drawers, for 23.3, 51.1, and 78.8 cu.ft models.
For REL-4504, roll-out drawer assembly, six additional stainless steel drawers, fully adjustable, fully extendable. 6703 For 29.2 cu.ft Models only For REL-3004, roll-out drawer assembly, six additional stainless steel drawers, fully adjustable, fully extendable. 6704 12 Thermo Scientific Forma Laboratory Refrigerators Installation and Operation Extended Warranty Options Note: In addition the standard full warranty on the complete product (USA and Canada), an additional four year protection on compressor and compressor parts can be supplied . This additional coverage must be purchased at the time of original product purchase. Under this contract, the manufacturer agrees to furnish a compressor FOB our factory to replace one which has been determined to be defective by manufacturer or a factory authorized Service Agency.
Extended Four-Year Compressor Parts Contract, all refrigerators.
Extended 12-Month Comprehensive Coverage, for all models, provides additional 12-month warranty coverage, parts and labor. Contact Customer Sales for details.
13 Thermo Scientific Forma Laboratory Refrigerators Installation and Operation WEEE Compliance WEEE Compliance. This product is required to comply with the European Union’s Waste Electrical & Electronic Equipment (WEEE) Directive 2002/96EC. It is marked with the following symbol. Thermo Fisher Scientific has contracted with one or more recycling/disposal companies in each EU Member State, and this product should be disposed of or recycled through them. Further information on our compliance with these Directives, the recyclers in your country, and information on Thermo Scientific products which may assist the detection of substances subject to the RoHS Directive are available at www.thermo.com/ WEEE Konformittät. Dieses Produkt muss die EU Waste Electrical & Electronic Equipment (WEEE) Richtlinie 2002/96EC erfüllen. Das Produkt ist durch folgendes Symbol gekennzeichnet. Thermo Fisher Scientific hat Vereinbarungen getroffen mit Verwertungs-/Entsorgungsanlagen in allen EU- Mitgliederstaaten und dieses Produkt muss durch diese Firmen widerverwetet oder entsorgt werden. Mehr Informationen über die Einhaltung dieser Anweisungen durch Thermo Scientific, dieVerwerter und Hinweise die Ihnen nützlich sein können, die Thermo Fisher Scientific Produkte zu identizfizieren, die unter diese RoHS. Anweisungfallen, finden Sie unter www.thermo.com/
Europea 2002/96EC in merito ai Rifiuti degli Apparecchi Elettrici ed Elettronici (WEEE). È marcato col seguente simbolo.Thermo Fischer Scientific ha stipulato contratti con una o diverse società di riciclaggio/smaltimento in ognuno degli Stati Membri Europei. Questo prodotto verrà smaltito o riciclato tramite queste medesime. Ulteriori informazioni sulla conformità di Thermo Fisher Scientific con queste Direttive, l’elenco delle ditte di riciclaggio nel Vostro paese e informazioni sui prodotti Thermo Scientific che possono essere utili alla rilevazione di sostanze soggette alla Direttiva RoHS sono disponibili sul sito
Conformité WEEE. Ce produit doit être conforme à la directive euro-péenne (2002/96EC) des Déchets d’Equipements Electriques et Electroniques (DEEE). Il est marqué par le symbole suivant. Thermo Fisher Scientific s’est associé avec une ou plusieurs compagnies de recyclage dans chaque état membre de l’union européenne et ce produit devraitêtre collecté ou recyclé par celles-ci. Davantage d’informations sur laconformité de Thermo Fisher Scientific à ces directives, les recycleurs dans votre pays et les informations sur les produits Thermo Fisher Scientific qui peuvent aider le détection des substances sujettes à la directive RoHS sont disponibles sur www.thermo.com/ Great Britain Deutschland Italia France Important For your future reference and when contacting the factory, please have the following information readily available: Model Number: Serial Number: Date Purchased: The above information can be found on the dataplate attached to the equipment. If available, please provide the date purchased, the source of purchase (manufacturer or specific agent/rep organization), and purchase order number. IF YOU NEED ASSISTANCE: SALES DIVISION Phone: 1-866-984-3766 (866-9-THERMO) LABORATORY PARTS and SERVICE Phone:
1-800-438-4851 TECHNICAL SUPPORT Phone: 1-800-438-4851 Thermo Fisher Scientific Inc. 275 Aiken Road Asheville, NC 28804 United States www.thermofisher.com 34830H
63 Rev. A Yüklə 0,98 Mb. Dostları ilə paylaş:
|