Tusa iq-650 element computer manual 12-2917-r02
Yüklə 3,03 Mb. Pdf görüntüsü
|
52 RESET PROCEDURE • While the Surface Sequence is scrolling, press/release the button (< 2 seconds) to access the Log Mode displaying the first screen of the most recent dive (Dive Preview/Identifier). • Press/release the button again (< 2 seconds) to access the second Log screen (Dive Data) of the most recent dive. • Depress/hold the button while the second Log screen of the most recent dive is being displayed to access the Reset screen. The graphics CLR and id will appear with the Key Code XXXX, the first 2 digits flashing (Fig. 60). Release the button. • If necessary to change the first 2 digits, press/release the button repeatedly (< 2 seconds each time) to select the correct number. • Depress the button for 2 seconds to save the first 2 digit number and advance to the second 2 digits, flashing. • If necessary to change the second 2 digits, press/release the button repeatedly (< 2 seconds each time) to select the correct number. • Once the proper Key Code has been entered, depress the button for 2 seconds to accept the Key Code, complete the Reset operation, and turn the unit Off (i.e., Clearing it). • If an incorrect Key Code number has been entered, the unit will revert to the Surface Sequence when the button is depressed, resuming previous operation(s). Fig. 60 - RESET (Clear)
53 GENERAL 54 CARE AND CLEANING Protect your Element from shock, excessive temperatures, chemi- cal attack, and tampering. Protect the lens against scratches with a transparent Instrument Lens Protector. Small scratches will naturally disappear underwater. • Soak and rinse the Element in fresh water at the end of each day of diving, and check to ensure that the areas around the low pressure (depth) sensor (Fig. 61a) and button are free of debris or obstructions. • To dissolve salt crystals, use lukewarm water or a 50% white vinegar/50% fresh water bath. After removal from the bath, place the unit under gently running water and towel dry before storing. • Transport your unit cool, dry, and protected. INSPECTIONS AND SERVICE Your Element should be inspected annually by an Autho- rized TUSA Dealer who will perform a factory prescribed func- tion check and inspection for damage or wear. To keep the product's warranty in effect, this inspection must be completed one year after purchase (+/- 30 days). TUSA recommends that you continue to have this inspection performed every year to ensure it is working properly. To Obtain Service Take your Element to an Authorized TUSA Dealer. Fig. 61 - BACK OF CASE a
55 NOTE: The procedures that follow must be closely adhered to. Damage due to improper battery replacement is not covered by the unit's warranty. MODULE REMOVAL FROM BOOT If the Module is in a Console, bend the rubber Console Boot back to expose the edge of the Module. If the Boot is flexible enough to permit, you may bend it back far enough to scoop the Module out with your finger. Otherwise, it may be necessary to insert a blunt screwdriver until the tip rests just underneath the Module. DO NOT pry the Module from the Console! Slowly increase the pressure under the Module by releasing the tension on the rubber Boot. The Module will slide up the screwdriver and exit the Console. If the Module is in a Wrist Boot, it will be necessary to peel the lips of the Boot downward off the Module while applying pressure from underneath, working it out slowly.
The Battery Compartment should only be opened in a dry and clean environment with extreme care taken to prevent the entrance of moisture or dust. To prevent formation of moisture in the Battery Compartment, it is recommended that the Battery be changed in an environment equivalent to the local outdoor temperature and humidity (e.g., do not change the Battery in an air conditioned environment, then take it outside during a hot sunny day).
56 Battery Hatch Removal • Locate the Battery Compartment on the back of the Module. • While applying steady inward pressure on the center of the Battery Hatch, rotate the Hatch Retaining Ring 10 degrees clockwise using a flat blade screwdriver (Fig. 62) or a Battery Hatch Tool. • Lift the Hatch Ring up and away from the Housing, or turn the Module over to allow it to drop out into your hand. • Remove the Battery Hatch.
• Remove the Retaining Bar located across the lower portion of the Battery (Fig. 63a). • Remove the Hatch O-ring. DO NOT use tools • Using care not to damage the Battery Contacts (Fig. 63b/c), slide the Battery up and out of the Battery Compartment. Inspection • Closely check all of the sealing surfaces for any signs of damage that might impair proper sealing. • Inspect the Button, Lens, and Housing to ensure they are not cracked or damaged. • If it is necessary to clean the Battery Compartment, flush it and all components with a solution of 50% white vinegar and 50% fresh water. Rinse with fresh water, and allow to dry overnight, or blow dry with a hair dryer (set at 'no heat'). Fig. 62 - RING REMOVAL Fig. 63 - HATCH REMOVAL a b c 57 WARNING: If damage or corrosion is found, return your Element to an Authorized TUSA Dealer, and DO NOT attempt to use it until it has received factory prescribed service. Battery Installation • Slide a new 3 volt type CR2450 Lithium Battery, negative ( - ) side down into the Battery Cavity. Slide it in from the right side and ensure that it slides under the contact clip on the left rim of the cavity (Fig. 64). • Orient the Retaining Bar across the lower portion of the Battery and carefully push it down into position (Fig. 65).
• Replace the Hatch O-ring with a new one which must be a genuine TUSA part. • Lightly lubricate the new Hatch O-ring with silicone grease and place it on the inner rim of the Battery Hatch (Fig. 66). Ensure that it is evenly seated. • Slide the Hatch Retaining Ring, top portion first (small open- ing), onto your thumb. • Carefully place the Battery Hatch (with O-ring) into position on the rim of the Battery Compartment, then press it evenly and completely down into place with your same thumb. Fig. 64 -INSERTING BATTERY Fig. 65 - INSERTING RETAINING BAR Fig. 66 - O-RING ON RIM OF HATCH
58 • Maintain the Battery Hatch securely in place and, using your other hand, slide the Retaining Ring down off your thumb and into position around the Battery Compartment. • The tabs on the Retaining Ring fit down into the two slots located at the 2 and 8 o'clock positions. • Using your fingers, turn the Ring counter clockwise 5 de- grees until the tabs engage (Fig. 67), then tighten it 5 more degrees by turning it counter clockwise using the Battery Hatch Tool (Fig. 68). • While tightening the Retaining Ring, exert continuous inward pressure on it until it is secured in the proper position. A small symbol located on the Ring should be aligned with the Locked symbol located on the Housing (Fig. 68a) Inspection • Activate the unit and watch carefully as it performs a full diagnostic and battery check, and enters Surface Mode. • Observe the LCD display to ensure it is consistently clear and sharp in contrast throughout the screen.
Fig. 68 -TIGHTENING the RETAINING RING Fig. 67 -ENGAGING the RETAINING RING TABS a
59 RETURNING THE MODULE TO BOOT • If the Boot was fitted with a Spacer and it was previously removed, replace the Spacer into the Boot. • Orient the Module over the opening in the Boot, and dip the bottom edge into it while pressing the top edge with the palm of your hand. Stop pressing when the bottom edge of the Module has just entered the Boot. • Correct the alignment of the Module as needed so that it is straight. • Press the Module completely into place with your thumbs, watching the alignment, until it snaps into place.
If your Element stops working for any reason, it is important that you have anticipated this possibility and are prepared for it. This is an important reason for not pushing
If you dive in situations where your trip would be ruined or your safety would be jeopar- dized by losing the use of your Element, a backup instrument system is highly recom- mended.
60 ALTITUDE COMPENSATION Atmospheric pressure decreases as Altitude increases above sea level. Weather systems and ambient temperature also affect barometric pressures. Consequently, depth reading instruments that do not compensate for the decrease in ambient pressure indicate depth readings shallower than the depth they are actually at. The Element automatically compensates for decreased ambient pressures for Altitudes between 3,001 feet (916 meters) and 14,000 feet (4,270 meters). Its program contains a high altitude algorithm that reduces no decompression and oxygen exposure limits to add a larger zone of caution. The Element senses ambient pressure when it is activated, every 15 minutes while it is activated, or every 30 minutes when it is not activated. At an Altitude of 3,001 feet (916 meters ), it will automatically recalibrate itself to measure depth in meters (feet) of fresh water rather than feet (meters) of sea water. It will then readjust the no decompression and oxygen limits at additional intervals of 1,000 feet (305 meters). When returning to lower Altitudes, diving should not be conducted until the unit automatically clears of any residual nitrogen and oxygen loading and resets to operate at the new lower Altitude. WARNING: The Element will not sense ambient pressures or provide Altitude compensation when it is wet. DO NOT dive at any different Altitude until the unit shuts off and is reactivated at the new Altitude. If the unit is activated at elevations higher than 14,000 feet (4,270 meters), it will perform a diagnostic check followed by immediate shutdown. 61 CAN BE USED AS • Air Computer • Nitrox Computer DIVE COMPUTER PERFORMANCE • Buhlmann ZHL-16c based Pelagic Z+ algorithm • No Deco limits closely follow PADI RDP • Decompression in agreement with Buhlmann ZHL-16c and French MN90 • No Deco Deep Stops - Morroni, Bennett • Deco Stops (not recommended) - Blatteau, Gerth, Gutvik • Altitude - Buhlmann, IANTD, RDP (Cross) • Altitude corrections and O2 limits based on NOAA tables
• Activation/Diagnostic • Serial Number • Surface
• Time to Fly Countdown • Desaturation Countdown • Pre Dive Planner 30 to 190 FT (9 to 57 M) • Dive Log (Preview, Dive Data, O2 Data) • Reset
• Set FO2 (Air, 21 to 50%) • Set Wet Activation (On / Off) • Set Units of Measure (Imperial / Metric) • Set Hour Format (12 / 24) • Set Time (Hour, Minute) • Set PO2 Alarm (1.20 to 1.60 ATA) • Set FO2 50% Default (On/Off) • No Decompression Dive: • Main
• Alt # 1
• Alt # 2 -only if nitrox dive • Deep Stop - for dives deeper than 80 FT (24 M) • Safety Stop - for dives deeper than 30 FT (9 M) • Decompression Stop: • Main
• Alt # 1
• Alt # 2
• Alt # 3 - only if a nitrox dive • Violation - Conditional, Delayed # 1, # 2, and # 3 • High PO2
• High O2
SPECIFICATIONS 62 DISPLAY RANGE/RESOLUTION Numeric Displays: Range:
Resolution: • Dive Number 0 - 12 1 • Depth 0 - 330 FT (99.9 M) 1 FT (0.1 M) • Maximum Depth 0 - 330 FT (99.9 M) 1 FT (0.1 M) • FO2 Set Point Air, 21 - 50 % 1 %
• PO2 Value 0.00 - 5.50 ATA .01 ATA
• Dive Time Remaining 0:00 - 9:59 hr:min 1 minute
• Total Ascent Time 0:00 - 9:59 hr:min 1 minute
• Decompression Stop Time 0:00 - 9:59 hr:min 1 minute
• Elapsed Dive Time 0:00 - 9:59 hr:min 1 minute
• Surface Time 0:00 - 9:59 hr:min 1 minute
( > 9:59 hr:min SI is displayed as Hours only 10-, 11-, 12-, etc.) • Dive Log Surface Interval 0:00 - 25:59 hr:min 1 minute
• Time to Fly 23:50 - 0:00 hr:min* 1 minute
(* starting 10 min after the dive) • Time to Desaturate 23:50 (maximum) - 0:00 hr:min* 1 minute (* starting 10 min. after the dive) • Temperature 0 to 99°F (- 9 to 60°C) 1°
Occurrence • Diagnostic Display After Manual Activation • Serial Number Display After Diagnostics (if the Button is held depressed until screen appears) • Out of Range (- - -) > 330 FT (> 99.9 M) • Gauge Mode Countdown Timer 23:50 to 0:00 hr:min (after Violation) SPECIFICATIONS (CONTINUED) 63 BAR GRAPHS Nitrogen Bar Graph segments
Oxygen (O2) Bar Graph: segments • 3 • Normal zone 3 • No Deco Caution zone 1 • Caution zone 1 • Decompression Warning zone 1 • Danger zone 1 Variable Ascent Rate Indicator: 60 FT (18 M) & Shallower Deeper than 60 FT (18 M) segments FPM
MPM segments
FPM MPM
0 0 - 10
0 - 3 0 0 - 20 0 - 6 • Normal Zone 1 11 - 25
3.5 - 7.5 1 21 - 50 6.5 - 15 • Caution Zone 2 26 - 30
8 - 9 2 51 - 60 15.5 - 18 • Too Fast Zone (flashing) 3 (all) > 30
> 9 3 (all)
> 60 > 18
OPERATIONAL PERFORMANCE Function: Accuracy: • Depth
±1% of full scale • Timers 1 second per day Dive Counter: • Displays Dives #1 to 12, 0 if no dive made yet. • Resets to Dive #1, upon reactivation after having shut off. SPECIFICATIONS (CONTINUED) 64 SPECIFICATIONS (CONTINUED) OPERATIONAL PERFORMANCE (continued) Dive Log Mode: • Stores 12 most recent dives in memory for viewing • After 12 dives, adds 13th dive in memory and deletes the first dive Altitude: • Operational from sea level to 14,000 feet (4,270 meters) elevation • Samples Ambient Pressure every 30 minutes when not activated, when manually activated, and every 30 minutes while activated. Does not sample Ambient Pressure while it is wet. • Adjusted No Decompression and O2 Limits and recalibration of depth readings at elevations between 3,001 feet (916 meters) and 14,000 feet (4,270 meters) at intervals of 1,000 feet (305 meters). Power: • Battery 1 - 3 vdc, type CR2450 Lithium battery • Shelf life Up to 5 years • Replacement User replaceable (annual recommended) • Life expectancy 100 dive hours (if 1 - 1 hour dive per dive day) to over 300 dive hours (if 3 - 1 hour dives per dive day) Activation: • Manual - push button (recommended) • Automatic - by immersion in water (if set ON) • WET graphic indicates Wet Contacts are bridged (unit must be dried prior to transport or storage) • Cannot be manually activated deeper than 4 FT (1.2 M), if the Water Activation feature is set OFF. • Cannot be activated at elevations higher than 14,000 feet (4,270 meters) Shut Off: • Automatically shuts Off if no dive is made within 2 hours after initial activation. Reactivation required. • Automatically shuts Off 24 hours after last dive (will reactivate if wet). • Cannot be shut Off manually. 65 OPERATIONAL PERFORMANCE (continued) Setting FO2: • Automatically set for AIR' upon activation • Remains set for AIR unless an FO2 numerical value is set • Nitrox Set Points from 21 to 50 % • If set for 21%, remains set for 21% until changed • If set for >21%, it reverts to 50% 10 minutes after the dive, if the FO2 Default is ON. If the FO2 Default is OFF, the value will remain at the value set for that activation period. Operating Temperature: • The Element will operate in waters having temperatures between 32°F and 140°F (0 and 60°C). At extremely low temperatures, the LCD may become sluggish, but this will not affect it's accuracy. If stored or transported in extremely low temperature areas (below freezing), you should warm the module and its battery with body heat before diving. SPECIFICATIONS (CONTINUED) 66 Tabata USA, Inc 2380 Mira Mar Avenue Long Beach, CA 90815 Tel: 562-498-3708 Fax: 562-498-0415 www.tusa.com info@tusa.com Tabata Australia PTY Ltd. Unit 11, 86 Falconer St. West Ryde, N.S.W. 2114 Australia Tel: 61-(0)2-9807-4177 Fax: 61-(0)2-9808-1638 www.tusa.com.au info@tabata.com.au Tabata Taiwan Co. Ltd. 54-8 Hsutsogang, Nankang Vil. Tayuan Hsiang, Tao Yuan Hsien Taiwan R.O.C. Tel: 886-(0)3-386-5100 Fax: 886-(0)3-386-5103 info@mail.tabata.com.tw Tabata Europe Corporation B.V. Den Brielstraat 2 B, 1055 RV Amsterdam, The Netherlands Tel: 31-(0)20 68 15 955 Fax: 31-(0)20 68 24 527 www.tusa.nl info@tusa.nl Tabata Co. Ltd. Japan 1-3-17 Higashikomagata, Sumida-ku Tokyo, Japan 130-0005 Tel: 81-(0)3-3624-2816 Fax: 81-(0)3-3623-9902 www.tusa.net info@tabata.co.jp TUSA INTERNATIONAL CONTACTS 67 SERVICE RECORD Serial No. & Rev. No. __________________ Date of Purchase _____________________ Purchased From _____________________ Below to be filled in by an Authorized TUSA Dealer: Date Service Performed Dealer / Technician Yüklə 3,03 Mb. Dostları ilə paylaş:
|