Convenient functions for playback and recording
Returning to the state before or after recording (Undo/Redo)
89
Convenient functions for
playback and recording
Returning to the state before or after
recording (Undo/Redo)
If you’re not satisfied with your performance and would like
to record it again, you can use the Undo function to return to
the state prior to recording. You can also step back through
multiple takes. If you want to cancel the Undo function, use
Redo.
1. To cancel the recording, press the UNDO (PAGE–)
button.
The UNDO dialog box will appear.
2. Specify the take that you want to use from the
previously-recorded takes, and press the OK button.
When
you execute UNDO, the UNDO button will be
highlighted.
Note: If you record in this state, the Redo data will be lost
and the UNDO button will return to its original appearance.
Specifying how recording will start
Use the Auto (Auto Rec Start) setting to specify how
recording will start automatically. You can make recording
start the moment you play a note on the keyboard, or when
the sequencer starts, or when the audio input signal reaches a
specific level.
Rec Start). For details, please see step 3.
2. Press the Rec Control
(MENU) button to enter
the record-standby condition. (AUDIO RECORDER
button: blinking orange)
3. Off: Press the Rec Control
(MENU) button or the
AUDIO RECORDER
button to start recording.
Note-On: Recording will start when you play the
keyboard.
SEQ START: Recording will start when you press the
SEQUENCER PLAY/STOP (
) button.
Input Low: Recording will start when the audio input
level exceeds approximately –18 dB.
Input High: Recording will start when the audio input
level exceeds approximately –6 dB.
Note: It’s convenient to record using the following method if
you want to overdub an external input
such as a guitar solo
or chorus onto a portion of the audio song.
1. Set Auto (Auto Rec Start) to Input Low or Input High.
Make input settings for Mic In.
2. Press the AUDIO RECORDER
button to start
playback. (AUDIO RECORDER button: lit green)
3. Slightly earlier than the point where you want to start
overdubbing, press the Rec Control
(MENU)
button to enter the record-standby condition.
(AUDIO RECORDER button: blinking orange)
4. Sing the chorus part. Recording will start
automatically in response to the input.
When you overdub using this method, the audio input from
0.2 seconds earlier than the moment you started recording
will actually be recorded. This lets you overdub without
losing the beginning of the chorus or guitar phrase.
Tip: This Auto (Auto Rec Start) setting can be stored in the
GLOBAL> PREF page as the default setting.
Loop playback
There’s a loop playback function
that lets you repeatedly
play a specified region (A–B) of an audio song.
Note: The loop play on/off setting and the specified time are
saved individually for each audio song.
This setting will be saved to the SD card when you
switch to a different audio song or when you turn off the
power. If you remove the SD card immediately after
select the setting, the setting will not be saved.
Using loop play
If you add a check mark to LOOP to turn it on, the playback
will loop.
To specify the loop region, set the point where looping will
start (point A) and end (point B).
Note: The interval between points A and B will be at least
three seconds.
It’s not possible to record while LOOP
has a check
mark. Nor is it possible to add a check mark to LOOP
during recording.
Setting the current time location as a point
There’s a convenient function that lets you directly specify
the current time location as one of the points. Move the cursor
to A or B, and press the ENTER button during playback; the
current time location will be specified as a point.
Note: If you use this method to specify the time location of a
point, the location will be specified with an accuracy of
within one second.
Audio recorder
90
Importing or exporting WAVE files
Importing
You can import a WAVE file into the audio recorder, and
play it or overdub onto it.
The following files can be imported.
• File format: WAVE format uncompressed linear PCM
• Sample bit depth: 16-bit
• Sampling frequency: 44.1 kHz or 48 kHz, stereo files?
Number of characters in file name:
The first eight characters
are shown
Note: Since 44.1 kHz WAVE files will be converted into 48
kHz as they are imported into the KROSS, a small amount of
time may be required.
Import procedure
1. Using your computer, copy the WAVE file that you
want to import into the KORG/KROSS/DATA folder
of an SD card that was formatted by the KROSS.
2. Access the MEDIA> FILE page.
3. Select the WAVE file that you want to import.
4. Choose the Load Selected function to access the dialog
box.
5. If you want to rename the song, access the text dialog
box and enter a name.
6. If the volume of the file you’re importing should be
adjusted beforehand, specify Level Adjust.
Note: After
importing, you can adjust the playback
volume of the audio recorder, or apply an individual
volume adjustment to each audio song. (see “Adjusting
the volume” on page 91)
7. Press the OK (MENU) button to execute the import
function.
The selected WAVE file will be loaded in KROSS audio
song format. The progress of execution is shown by a
progress bar in the display.
Note: This may take some time depending on the type of
file, etc.
During the import procedure, you can cancel by pressing
the ABORT (FUNCTION) button.
8. In the audio recorder setup window, select the song
that you imported, and play it.
Exporting a WAVE file
A multitrack-recorded audio song can be exported as a
WAVE file to the KORG/KROSS/DATA folder of the SD
card.
This lets you use your audio player to listen to an audio song
produced on the KROSS, or to load the song into your DAW.
• File format: WAVE format uncompressed linear PCM
• Sample bit depth: 16-bit
• Sampling frequency: 48 kHz
Number of characters in file name: The first eight characters
are shown
Export procedure
1. In the audio recorder setup window, select the audio
song that you want to export.
2. Choose the Export function to access the dialog box.
3. If you want to rename the file, access the text dialog
box and enter a name.
4. If you want to adjust the audio level of the song when
exporting it, specify Level Adjust.
5. Press the OK (MENU) button to execute the export
function.
The selected audio song will be exported as a WAVE file.
The progress of execution is shown by a progress bar in
the display.
The WAVE file will be created in the KORG/KROSS/
DATA folder of the SD card.
Note: This may take some time, depending on the length
of the song.
During the export procedure, you can cancel by pressing
the ABORT (FUNCTION) button.