64
Cockpit
The multifunction system uses two automatic memories:
1 - Actual
memory and
2 - Total memory. The selected memory will be shown
in the upper right-hand corner of the display.
Selecting a memory
– When the ignition is on, briefly press button
⇒ fig. 39
A
on the
windscreen wiper lever to change from one memory to another
or press button
A
on the steering wheel controls
⇒ fig. 39
.
Resetting a memory
– Select the memory that you would like to reset.
– Hold
down button
A
on the windscreen wiper lever or button
A
on the steering wheel controls for at least 2 seconds.
The
trip memory 1 collects the travel and consumption rates from the mo-
ment the ignition is switched on until it is switched off. If the journey is con-
tinued within two hours of switching off the ignition, the new values will be
added to the existing trip recorder memory. The memory will automatically
be deleted if the journey is interrupted for more than two hours.
The
total memory 2 collects the trip data for any number of individual jour-
neys (even if the ignition is switched off for longer than two hours) up to a
total of 19 hours and 59 minutes travel time or 1999 km distance travelled.
The memory will automatically be deleted if one of the named values is
reached.
Information in the multifunction display (MFI)*
Fig. 41 Rocker buttons A
and B. Steering wheel
controls.
Fig. 42 Digital instru-
ment panel display: aver-
age fuel consumption in-
dicator.
You can switch between the following displays in the multifunction display
(MFI) by operating rocker switch
⇒ fig. 41
B
on the windscreen wiper lever.
65
Cockpit
Memory displays
● Driving speed
● Journey duration
● Average speed
● Distance
● Distance to empty
● Average fuel consumption
● Current fuel consumption
●
Outside temperature display
● Speed warning
Km/h - Driving speed
Driving speed is digitally shown in the display.
min
- Journey duration
The display shows the amount of time which has elapsed
since the ignition
was switched on.
The maximum display value in both memories is 19 hours and 59 minutes.
The memory will automatically be deleted once this value has been
reached.
Ø mph
- Average speed
The average speed will be shown after running a distance of approximately
100 metres. Until then dashes will appear in the display. The display will be
updated every 5 seconds while the vehicle is in motion.
km
- Distance travelled
The display shows the distance travelled since the ignition was switched on.
The maximum display value in both memories is 1999 km. The memory will
automatically be deleted once this value has been reached.
Km
- Fuel range
The fuel range is calculated using the figures for tank content and current
fuel consumption. It shows how far the vehicle can travel using the same
conditions as a reference.
Ø ltr/100km
- Average fuel consumption
The average fuel consumption will be shown
⇒ fig. 42
after a distance of ap-
proximately 100 metres has been travelled. Until then dashes will appear in
the display. The display will be updated every 5 seconds while the vehicle is
in motion. The amount of fuel used will not be shown.
l/100 km
or
l/h
- Current fuel consumption
The display will show the current fuel consumption in litre/km whilst the ve-
hicle is in motion or in litre/hour when the vehicle is in a stationary position
with the engine running.
Using this display you can see how your driving style affects fuel consump-
tion
⇒ page 191.
Outside temperature display
The measurement range extends from -45°C to +58°C.
At temperatures be-
low +4°C, an ice crystal symbol is displayed and a warning sounds if the ve-
hicle is moving at more than 20 km/h (ice danger warning). This symbol will
flash for about 10 seconds and remains lit until the outside temperature
rises above +4°C or 6°C if it was already lit.
Set speed indicator
When driving at the required speed, enter the speed indicator mode and
press the button
A
(Reset), the display remembers the indicated speed. If
the indicated speed is exceeded, a warning message is displayed on the
screen
1)
and an acoustic signal is given.
1)
Depending on the model version, the message on the screen
may vary and may be repre-
sented by flashing of the speed indication or by a speed message.
Safety First
Operating Instructions
Practical Tips
Technical Specifications
66
Cockpit
This may be deactivated by pressing the button
A
(Reset).
The speed may be altered using the rocker switch
B
in steps of 5 km/h
within 5 seconds of the initial memory value.
WARNING
There could be black ice on the road surface even if the “snowflake sym-
bol” is not shown. For this reason you should not rely exclusively on this
display - Risk of accident!
Note
When the vehicle is stationary or travelling at very low speeds, the tempera-
ture displayed may be slightly higher than the actual outside temperature
as a result of the heat radiated from the engine.
Warning or information message in the display
Faults are shown in the display with warning lamps and
warning/information reports.
The system runs a check on certain components and
functions when the ig-
nition is switched on and while the vehicle is moving. Functional faults are
indicated by symbols with warning or information messages in the display.
An acoustic warning is given in certain cases.
Warning symbols
There are red warning symbols (priority 1) and yellow warning symbols (pri-
ority 2)
Information text
In addition to warning messages given on a fault, you will receive informa-
tion in the display on procedures or will be asked to carry out certain tasks.
Note
In the case of screens without warning or information texts, faults are indi-
cated exclusively by the warning lamps.
Warning reports, Priority 1 (red)
If one of these faults occurs, the warning lamp will flash or light up and will
be accompanied by
three audible warnings. This is a
danger warning. Stop
the vehicle and switch off the engine. Check the fault and correct it. Obtain
professional assistance if necessary.
If several priority 1 faults are
detected at the same time, the symbols will be
displayed one after the other for about 2 seconds at a time and will contin-
ue until the fault is corrected.
No menus will be shown in the display for the duration of a priority 1 warn-
ing message.
Examples of priority 1 warning messages (red)
● Brake system symbol with the warning message
STOP BRAKE FLUID
SERVICE MANUAL
or
STOP BRAKE FAULT SERVICE MANUAL
.
● Coolant symbol with the warning message
STOP SEE COOLANT IN-
STRUCTION MANUAL
.
● Engine oil pressure symbol with the warning message
STOP ENGINE
OIL PRESSURE LOW! INSTRUCTION MANUAL
.
Warning reports, Priority 2 (yellow)
If one of these faults occurs,
the warning lamp lights up, and is accompa-
nied by
one audible warning. The function should be checked as soon as
possible.
